Minimum requirements for CD recording on an A2500?

[DoomMaster]

What are the minimum requirements for CD recording on an Amiga 2500?  I have the Revision 6.3 motherboard, a 68030 board, 9 megs of memory, an A2091 SCSI card, a Seagate 7200 RPM hard disk and a Plexter CD-RW drive.  Do I need anything else and what software do I use?  Please, no bs or ego trips.  Thanks.     :-D

[iamaboringperson]

Those smilies are fun aren't they "DoomMaster"?

Look at this one -> ':-D' And howabout this: ':-o'

This one is really fun too! -> :lol:

Lot's of fun can be had with those!

:-D

[KennyR]

You'll need MakeCD or BurnIT software packages, both are commercial but you can try out the demos on Aminet.

But I'll tell you this right now: you're going to struggle to be able to burn with an 030 and 9MB of ram.

[JurassicCamper]

@ doomy I promise i wont take the P!$$

But....

Why the chuffin heck are you trying to do it on an Amiga when it says in your sig you have an P4  :-P  ?

On a serious note. A CD is 800 Meg Roughly so say at least double if you want to work with full CD's.

If you want to edit CD's / Songs

Memory should not be a problem as you dont have enough to do RAM editing anyway, so you you'll be using hard disc based project.

Recording CPU wise you should be OK Editing wise forget it. I find HD editing 60-70 meg AIFF files slow even on an 060.

I recommend Samplitude Opus / AHI Record You will need a sampler as well such as the excellent Meglosound from hisoft.

If you want to burn mp3's straight back to CDROM on the fly then you'll need mpega.library and a burn proof writer that does not suffer from under runs.

Saying that bin the 2000 get a 1200, stick a mediator in it, an 060, soundblaster 128, voodoo 3 and you'll be sorted.

 :-P

[amigamad]

Saying that bin the 2000 get a 1200, stick a mediator in it, an 060, soundblaster 128, voodoo 3 and you'll be sorted.

I agree your border line with that slow 030 an 060 a1200 is much better and ppc card is better still .You are limited by your militry spec professional machine because you only have 9 meg of memory my toy a1200 has a 160 megs of memory which makes your computer look even more dated . :-)

[x56h34]

PPC at this time doesn't make any difference about the burning speed, with Amiga OS3.x. There are only 68k burning apps available at the moment, so a 68060 CPU is the best you can get. I doubt that there would be much, if any defference between an A2000 with Blizzard 2060 and an A1200 with Blizzard 1260, unless of course you use Fast ATA controller on the A1200 which is a bit faster than the Blizzard Fast SCSI-2 controller, however with no DMA.

[DoomMaster]

I do not care about burning music to CDs.  I can do that on my Pentium 4 machine.  All I want to do is burn SOFTWARE (games, productivty, MODs, pictures, etc) onto Amiga formatted CDs, so that I do not have to change the names of the files.  I want to be able to run Amiga programs from the CD or copy the folders containing those programs to my Amiga hard disk.     :roll:

[amiga1260]

I used to burn cd's with my Amiga 1200 with a 68030 at 50 MHz. The maximum burning speed I could burn safely was 4 speed, but if you buy a CD-Rewriter with burnproof, you could burn at higher speed. The software I used were AsimCDFS 3.10 and MasterISO 2.4. Version 2.5 has some problems with my Blizzard 1230 SCSI-kit. I haven't try to use makeCD or Burnit.  I think 8 MB of RAM is enough to burn a CD. I have in that machine 48 MB of RAM.

[DoomMaster]

To KennyR:

But I'll tell you this right now: you're going to struggle to be able to burn with an 030 and 9MB of ram.

Why is that?  All I want to do is format Amiga CDs and copy files to the CDs.  What I already have should be MORE then enough to do this.     :-o

[amigamad]

do not care about burning music to CDs. I can do that on my Pentium 4 machine. All I want to do is burn SOFTWARE (games

Hope there not copyright games .

Makecd is one of the best cd programs and if you find your 030 is not fast enough you could reduce the burning speed down. on my a1200 with ppc it is an 040 at 25 mhz that is used with out problem for cd burning  but the writer in the system is only a crapy 2 speed memorex.A faster drive with burnproof would be your best option. :-)

Im sure your 9 meg of memory should be enough . the program itself does not need much memory.

[DoomMaster]

To amiga1260:

Thanks for your reply.  Recording a CD-R at 4 speed will be just fine.  I burn at that speed on my Pentium 4 computer anyway, even though my CD-RW drive can burn at 36 speed.  I found out that low speed (4X to 8X) single-session burned CD-Rs are the most reliable.  Reliability is more important to me then speed.  I am in no hurry, so recording software onto CD-Rs at 4 speed will be just fine, just as long as the content on the CD will last for at least 100 years on CD-R Pro Archival Quality CDs.     :-D

[DoomMaster]

To amigamad:

I also have an 040 board, but I actually prefer the Commodore 030 card.  On the 040 board I can install up to 32 megs of 32-bit memory.  Do you think the 040 board will make a difference?  If it does, then I will try it.     :-P

[Tomas]

I think magnetic tape is better to store data for 100 years...
Recent tests say that cdrs are not very reliable, not even the more expensive brands... the data will just end up getting corrupted in 20 years or so...  :-(

[DoomMaster]

To Tomas:

[color=FF0033]HUH ?![/color][/b]     :-o

[Cass]

@ Doomie

I've been writing CDs with a 030@25 and 18MB (16 fast & 2 chip) ram, using MakeCD. If you want to make CDs for backup-storage etc, then speed won't be an issue (what matters is to have the CD with an Amiga FS, protection bits & file comments). So try to create ISO image files first, and then burn the ISO at minimum/single speed... (to avoid buffer underruns).
________
Honda j-vx