Warp3d ramlib error ppc task error???????help!!

[tolishot]

maybe is memory the problem?
?
wrong settings in configuration menu on ppc?
post the congiguration menu ppc here to compare the chenges!thanks!

[doctorq]

It most likely doesn't help posting memory settings here, since neither are using the same ram modules.

I have mine set to 60 ns, and my 256 MB ram doesn't complain :-)

[tolishot]

hmm!me too!also!the 2 memory 2x128mb in 60ns the 1200 crashes!
in 70ns worked fine!tell me if you know doctorq:the free config is better?or kneeds some settings? :rtfm:

[doctorq]

@tolishot

Dunno, 60 ns has always worked for me. If your memory modules are rated at 60 ns and the computer crashes, I would think there is a problem with the memory modules, or the memory controllers on the accelerator.

By the way, your overclocking of the board can also be the reason since the timing of the board has been altered.

[CLS2086]

I had this problem in time.
It was due to a bad install of 3.9 BBx and warp version...
A friend of mine send me a backup of his install, and all works.
Now this install works well with GREX+Voodoo 3-3000 and GREX+Permedia2 and BVision too.

[Doraemon]

Yes, I have
68040.library 46.5
68060.library 46.7
Warpup V5.1
Cgxv42_rc6 <- I found a mistake!!!!!!

Were can I download the last (doctorq said that exist a 43.4_rc6)? vgr.com its dead and powerup.amigaworld.de doesn't have it.

The settings of the ppc bios are
Ram at 70ns

System:
No maprom
No 31khz screen
Superscalar ON
BranchCache ON
WriteBuffer ON

I have 2x128 mb simms that I bougth at amigakit. Amigakit says that simms are at 60 ns but it doesnt have any inscription about velocity and if I put it to 60 doesnt boot.

Ahh, I tryed some diferent ppc flash that i fount in grex.amigaworld.de but seems thats especifically for grex and the bvision doesn't work with it. Only works fine with the version on powerup.amigaworld.de

Any ideas?

[doctorq]

Were can I download the last (doctorq said that exist a 43.4_rc6)?

Most likely I'm mistaken on that one.

[tolishot]

the settings of the ppc bios on me dose not shows all of them.
only two settings is availiable!
nomaprom and
no 31khz default screen.all the others is in the shadow.
any ideas?? :-?

[CLS2086]

Ahh, I tryed some diferent ppc flash that i fount in grex.amigaworld.de but seems thats especifically for grex and the bvision doesn't work with it. Only works fine with the version on powerup.amigaworld.de

Strange, very strange. My 2 BPPC worked with before and after got updated to rev2 by DCE.

How large is your stack ?
Did you install IDEFIX ?

[tolishot]

yes i have install all latest!
my ppc is phase 5 no dce!

[Piru]

@Doraemon

Ahh, I tryed some diferent ppc flash that i fount in grex.amigaworld.de but seems thats especifically for grex and the bvision doesn't work with it.

Worked fine here, on CGX4.

[CLS2086]

So it's a faulty card or you have a virus...
did you try the "FORCE" parameter to flash your card ?

[Doraemon]

No, I don't user FORCE, you recomend it?

Now I go to make a exam (SHIT!) when I return to home I will test another time the grex flashes and I check my system with a antivirus program.

[Doraemon]

Its enought that when my amiga its turned on, I get in +5v pins 4.7V ?
Its a adapted Atx p4 power supply of 400W.
It might be a problem?
Im using the power conecter of floppy trick.

[Lando]

Doraemon wrote:
Its enought that when my amiga its turned on, I get in +5v pins 4.7V ?
Its a adapted Atx p4 power supply of 400W.
It might be a problem?
Im using the power conecter of floppy trick.

You're supplying power to the Amiga through the floppy connector alone?  This is not enough.

First the floppy connector doesn't have -12V (so sound and serial port won't work) and also sufficient power cannot be forced down the PCB tracks.

You must also power the Amiga through the square power connector at the same time (using the same ATX PSU - you can splice an old Amiga PSU connector to the cables).  Also power the fan on the BPPC directly from the PSU so it's not drawing power from the motherboard.

Otherwise your system could be very unstable and may not even work at all.

[CLS2086]

Yes all of that is right.
But 4.7v is too low ! Change your PSU for a better one that can give you more than 4.86v for +5v in "charge".