Warp3d ramlib error ppc task error???????help!!

[Boot_WB]

Soory, have been using WhichAmiga in the last couple of days to check my PPC was working, I think your name got stuck. :-)

Frank Willie was the BPPCfix author I believe (sorry Frank :-)).

BTW - I thought WhichAmiga needed ppc.library (or ppclibemu) to be active to detect  the PPC?  I have BPPCfix and WarpOS installed, with no ppc.library emulation, and WhichAmiga still seems to be detecting my PPC.  Did you fix this in later versions?

[Piru]

@Boot_WB

BTW - I thought WhichAmiga needed ppc.library (or ppclibemu) to be active to detect the PPC? I have BPPCfix and WarpOS installed, with no ppc.library emulation, and WhichAmiga still seems to be detecting my PPC. Did you fix this in later versions?

WhichAmiga works with both PUP and WOS.

[Boot_WB]

tolishot wrote:but this problem i dont understund why the resolution of my bzvppc is only 320x480 to 800x600?

You probably have 1024*768 available in 8-bit, but not in 15, 16, or 24-bit.

Try running Prefs/cgxmode to set up additional screen resolutions.

the steps to setup from begining the bvppc card to show the resolution in screenmodes!thanks! :getmad:  :getmad:

Erm, not sure I understand, but once you have installed CGX, selecting BVision as your graphics card there should be a BVisionPPC file shown in devs/monitors.
Once you have rebooted the BVision screenmodes should be visible in prefs/screenmodes.
Any additional resolutions you set up using prefs/cgxmode will become visible in prefs/screenmode after rebooting.

[tolishot]

look!i dont know if my ppc 603e had problem but if it is problem why some programs runs?like warpos? like warptest warp gears68k? warp engine shows  in 320x280 about 65 fps!it is ok?

[Boot_WB]

Piru wrote:
WhichAmiga works with both PUP and WOS.

Thanks, I was mis-informed:

Lordspider wrote:
BTW: Do you use BPPCFix? If so, WhichAmiga won't show the PPC info, you have to install the ppclibemu ppclibemu first.

here.

[Framiga]

try to UNselect "Memory Protection" (if selected) from WarpOS settings. (save and reboot)

Sometimes it helps with W3D programs.

Then try also to run SnoopDos before to run Gears. (just to slowdown the W3D init/loading) sometimes it helps too :-)

[Boot_WB]

tolishot wrote:
look!i dont know if my ppc 603e had problem but if it is problem why some programs runs?like warpos? like warptest warp gears68k? warp engine shows  in 320x280 about 65 fps!it is ok?

Gears 68k only uses the 680x0 processor, and just tests your warp3d configuration.

Please run the following tests:

Gears 68K - runs on 680x0:
Does it run full screen?  
Does it run in a window?

Gears PPC - runs on 603e PPC processor:
Does it run full screen?
Does it run in a window?

[tolishot]

gears 68k works fine but slow.
gears 68k window dont run .
gearsppc white screen or exception page ppc task error.
gearsppc window. the same.
glsokoban the same.
engine works fine with good fps.
when he calls ppc task is the problem.then exception page.
i am confused.sorry !!
but i tryning to fix this problem.i loose my mind in this amiga.if it something is wrong i cant see!new configuration!latest programs with updates!i cant solved the problem!!!!! :madashell:  :madashell:  :madashell:  :pissed:

[Doraemon]

I discovered that my problem is not with W3d.
I have problems with all the warpos things that uses the bvision (in 2d, or in 3d)
The warp3d demos in aga runs fine, but in the graphic card crashes.

MynCgx4prefs are
Supergels 1
HiresCRSR 1
usesemaphores 1
All the other vars to 0

My Warpos prefs are:
memory protection 0
no ppc 0
early term 0
Terminator 2
Hide warning 1
no patch 0
Always use videoadress
Hex:E0000000
No debugging
Segment info 1

Im using the original bppcfix but I tyed too blizzckik with the bppcfix without luck.

I obtained a few seconds more of w3d run using stackattack.

Anyone can see something wrong ?

[tolishot]

your video address is correct?check your bvppc is the same video address?i have the same settings too! :-D

[Doraemon]

How can I check if thats the correct videoadress of my bvision ?
Thx

[doctorq]

@all

These are the envs I have on my A1200T with BPPC 040/160/SCSI and BVisionPPC. All demos of WarpUP and Warp3D (except Engine) works.

PowerPC:

      alertfile : CON:0/20/400/200/WarpOS - System Message/AUTO/CLOSE/WAIT/INACTIVE
      crashfile : CON:0/20/400/300/WarpOS - PowerPC Exception/AUTO/CLOSE/WAIT/INACTIVE
      debug : 0
      earlyterm : 0
      hidewarning : 0
      terminator : 2
      seginfo : 100
      gfxaddr : $e0000000
      force : 1
      memprot : 1
      EnAlignExc : 1
     
CyberGraphX:
     
      CGXHELPPATH : HELP:
      ALERTEMU : 0
      CPUP2C : 0
      HIDE15BIT : 1
      HIRESCRSR : 1
      NOPASSTHROUGH : 1
      PLANES2FAST : 1
      SAVEMEM : 1
      SUPERGELS : 1
      SUPERLAYERS : 1
      WBPATSPEEDUP : 1
      BVisionPPCMonitor : Monitor-57KHz
      USESEMAPHORES : 1
      KEEPAMIGAVIDEO : 1

VoxelSpace in full screen 8 bit 320 x 240 gives around 55 Hz in average.

[tolishot]

in my voxelspace in full screen 320x240 8bit gives about 68-70 hz.:)on me work engine, gears68k,and warptest.i push my ppc on 266mhz and 68040 in 30 mhz.i put ram in 50-60ns.and the config menu on ppc is 60ns the ram. :rtfm:

[Doraemon]

Im using your settings doctorq and I have the same problem

[doctorq]

@Doraemon

OK, but have you got the latest libraries installed for both 68k CPU, PPC CPU and CyberGraphX?

IIRC latest 68k libraries are 46.5 and 46.7, WarpUP libraries v5.1, and latest update of CGX v4 is 43.4_rc6 IIRC.

[tolishot]

maybe is memory the problem?
?
wrong settings in configuration menu on ppc?
post the congiguration menu ppc here to compare the chenges!thanks!