Welcome, Guest. Please login or register.
Forums
« previous next »
Pages: 1 [2] 3   Go Down

Author Topic: CF ide for Amiga1200 problem, Please help  (Read 6101 times)

Description:

0 Members and 1 Guest are viewing this topic.

Offline Jabaruk1

  • Newbie
  • *
  • Join Date: Dec 2004
  • Posts: 40
    • Show only replies by Jabaruk1
    • http://www.jabar.karoo.net
Re: CF ide for Amiga1200 problem, Please help
« Reply #14 on: June 24, 2006, 09:38:04 AM »
I have put together and sold 11 of these CF to IDE, I had same problem here with some CF cards in the end i used a program called RDprep (http://it.aminet.net/disk/misc/rdp391.lha) for some cards and an older unknown HD setup program (will find name when have time),these cards would not be seen by HDTools but older software found them odd i know ,also the current setup needs no power it all comes from the 1200 built in IDE.
Logged
 

Offline bakoulisTopic starter

  • Full Member
  • ***
  • Join Date: May 2006
  • Posts: 170
    • Show only replies by bakoulis
Re: CF ide for Amiga1200 problem, Please help
« Reply #15 on: June 24, 2006, 09:42:18 AM »
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=18871&item=7628691125
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=41993&item=9738787726
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=41993&item=9739426636
That is my hardware plus 2 more older cf cards (16mb hitachi & 256mb sandisk).
The truth is I have the idefix adapter, but not only test it with idefix adapter. I have tried to connected the "2.5 ide to cf" on amiga original 2.5 ide port (without idefix board offcourse) not works again. The led of adapter blinking when amiga boots. Blinking again when hdtoolbox scaning for devices, but don't seen the cf cards as hd. :crazy:
________
IOLITE VAPORIZER REVIEW
« Last Edit: May 02, 2011, 09:32:17 PM by bakoulis »
Logged
Amiga4000/18MB/040/LAN/RTG, Amiga1200HD/6MB, Amiga1200HD, Amiga3000/10MB/RTG, Amiga2000HD/17MB/030/LAN/RTG, Amiga1000/2.5MB, Amiga600/3MB, Amiga500/1MB 1.2, 2xAmiga500/1MB 1.3, Amiga500+/2MB, CDTV Expanded, CD32 Expanded.
 

Offline rare_j

  • Jr. Member
  • **
  • Join Date: Mar 2006
  • Posts: 85
    • Show only replies by rare_j
Re: CF ide for Amiga1200 problem, Please help
« Reply #16 on: June 24, 2006, 10:03:03 AM »
I use the sintech "IDE to CF (Compact Flash) Adapter for Laptop #44-pins"

You must use a jumper on this board to make the CF card the master device. Check your jumper is on and also check the jumper pins on the board are straight and are making good contact with the jumper.
Logged
 

Offline Jabaruk1

  • Newbie
  • *
  • Join Date: Dec 2004
  • Posts: 40
    • Show only replies by Jabaruk1
    • http://www.jabar.karoo.net
Re: CF ide for Amiga1200 problem, Please help
« Reply #17 on: June 24, 2006, 10:12:30 AM »
Logged
 

Offline bakoulisTopic starter

  • Full Member
  • ***
  • Join Date: May 2006
  • Posts: 170
    • Show only replies by bakoulis
Re: CF ide for Amiga1200 problem, Please help
« Reply #18 on: June 24, 2006, 02:43:37 PM »
Quote

Jabaruk1 wrote:
I have put together and sold 11 of these CF to IDE, I had same problem here with some CF cards in the end i used a program called RDprep (http://it.aminet.net/disk/misc/rdp391.lha) for some cards and an older unknown HD setup program (will find name when have time),these cards would not be seen by HDTools but older software found them odd i know ,also the current setup needs no power it all comes from the 1200 built in IDE.


Also this program didn't seen my cf. And fail to seen correctly my IBM 4,0GB HD (without partitions and as 12,48MB IBM!!!) terrible. I give up. :boohoo:
________
WELLBUTRIN CLASS ACTION
« Last Edit: May 02, 2011, 09:32:36 PM by bakoulis »
Logged
Amiga4000/18MB/040/LAN/RTG, Amiga1200HD/6MB, Amiga1200HD, Amiga3000/10MB/RTG, Amiga2000HD/17MB/030/LAN/RTG, Amiga1000/2.5MB, Amiga600/3MB, Amiga500/1MB 1.2, 2xAmiga500/1MB 1.3, Amiga500+/2MB, CDTV Expanded, CD32 Expanded.
 

Offline PG

  • Full Member
  • ***
  • Join Date: Feb 2004
  • Posts: 221
    • Show only replies by PG
Re: CF ide for Amiga1200 problem, Please help
« Reply #19 on: June 24, 2006, 02:57:53 PM »
Quote

bakoulis wrote:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=18871&item=7628691125
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=41993&item=9738787726
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=41993&item=9739426636
That is my hardware plus 2 more older cf cards (16mb hitachi & 256mb sandisk).
The truth is I have the idefix adapter, but not only test it with idefix adapter. I have tried to connected the "2.5 ide to cf" on amiga original 2.5 ide port (without idefix board offcourse) not works again. The led of adapter blinking when amiga boots. Blinking again when hdtoolbox scaning for devices, but don't seen the cf cards as hd. :crazy:


In HD toolbox: hit the "change drive type" button, then "Define new..." and after that "Read Configuration".
Give the drive a name and hit the "ok" button (never mind the "unit is not a dos disk" error message).
Now you should be able to partition your cf-card in hd toolbox.
Logged
 

Offline bakoulisTopic starter

  • Full Member
  • ***
  • Join Date: May 2006
  • Posts: 170
    • Show only replies by bakoulis
Re: CF ide for Amiga1200 problem, Please help
« Reply #20 on: June 24, 2006, 09:34:08 PM »
Quote


In HD toolbox: hit the "change drive type" button, then "Define new..." and after that "Read Configuration".
Give the drive a name and hit the "ok" button (never mind the "unit is not a dos disk" error message).
Now you should be able to partition your cf-card in hd toolbox.


In hdtoolbox didn't present the cf card as unknown or whatever. The hd toolbox find only my IBM 4.0GB hd.
If I'll hit the "change drive type" button and "define new" this action will remove all data from my HD. Anyway... now I know this project isn't works for me but I don't know why.
 :getmad:
________
Depakote death
« Last Edit: May 02, 2011, 09:32:51 PM by bakoulis »
Logged
Amiga4000/18MB/040/LAN/RTG, Amiga1200HD/6MB, Amiga1200HD, Amiga3000/10MB/RTG, Amiga2000HD/17MB/030/LAN/RTG, Amiga1000/2.5MB, Amiga600/3MB, Amiga500/1MB 1.2, 2xAmiga500/1MB 1.3, Amiga500+/2MB, CDTV Expanded, CD32 Expanded.
 

Offline Jabaruk1

  • Newbie
  • *
  • Join Date: Dec 2004
  • Posts: 40
    • Show only replies by Jabaruk1
    • http://www.jabar.karoo.net
Re: CF ide for Amiga1200 problem, Please help
« Reply #21 on: June 24, 2006, 10:07:28 PM »
Dude i dont like to plug in Amiga.org  but PM me and we will sort you out a working CF to IDE at cost i would rather see you with a working option than getting miffed off over our beloved amiga.
Logged
 

Offline PG

  • Full Member
  • ***
  • Join Date: Feb 2004
  • Posts: 221
    • Show only replies by PG
Re: CF ide for Amiga1200 problem, Please help
« Reply #22 on: June 24, 2006, 10:46:51 PM »
Quote

bakoulis wrote:
Quote


In HD toolbox: hit the "change drive type" button, then "Define new..." and after that "Read Configuration".
Give the drive a name and hit the "ok" button (never mind the "unit is not a dos disk" error message).
Now you should be able to partition your cf-card in hd toolbox.


In hdtoolbox didn't present the cf card as unknown or whatever. The hd toolbox find only my IBM 4.0GB hd.
If I'll hit the "change drive type" button and "define new" this action will remove all data from my HD. Anyway... now I know this project isn't works for me but I don't know why.
 :getmad:


Are you using your IDE-fix adapter..?

Try this:

1. You should have only your CF-IDE adapter (with CF card installed) connected to the IDE port.
2. Start with wb3.0 or 3.1 Install disk and start HD toolbox from the diskette.

Now HD toolbox should find your card.
Then follow the steps from my previous post.
It should work.
Logged
 

Offline bakoulisTopic starter

  • Full Member
  • ***
  • Join Date: May 2006
  • Posts: 170
    • Show only replies by bakoulis
Re: CF ide for Amiga1200 problem, Please help
« Reply #23 on: June 25, 2006, 12:48:14 PM »
Are you using your IDE-fix adapter..?

Try this:

1. You should have only your CF-IDE adapter (with CF card installed) connected to the IDE port.
2. Start with wb3.0 or 3.1 Install disk and start HD toolbox from the diskette.

Now HD toolbox should find your card.
Then follow the steps from my previous post.
It should work.
[/quote]
It isn't work with or without idefix, but even was worked without idefix I wasn't happy without cd-rom

________
GLASS WEED PIPE
« Last Edit: May 02, 2011, 09:33:04 PM by bakoulis »
Logged
Amiga4000/18MB/040/LAN/RTG, Amiga1200HD/6MB, Amiga1200HD, Amiga3000/10MB/RTG, Amiga2000HD/17MB/030/LAN/RTG, Amiga1000/2.5MB, Amiga600/3MB, Amiga500/1MB 1.2, 2xAmiga500/1MB 1.3, Amiga500+/2MB, CDTV Expanded, CD32 Expanded.
 

Offline PG

  • Full Member
  • ***
  • Join Date: Feb 2004
  • Posts: 221
    • Show only replies by PG
Re: CF ide for Amiga1200 problem, Please help
« Reply #24 on: June 25, 2006, 02:49:32 PM »
Ok, its strange that hd toolbox cant find your card(s).
I know that at least your 256Mb Sandisk card + 44-pin adapter should work (but not in a master-slave chain) because i have tested it myself.
Maybe it isnt compatible with all mainboard revisions if you cant get it working.

About the cd-rom and cf-card:
1.There is two options: use a Elbox splitter or Fast Ata (should work but i have not tested it myself).
DONT use a ide-fix adapter, because the software is not compatible with CF cards.

2.Use a Lexar CF card, at least i know 512Mb cards and less capacity works, those i have tested.
Set up a master-slave chain with the internal IDE interface and install for example the CD-Rom software included in OS3.5 or 3.9.
That works fine!
Logged
 

Offline sir_inferno

  • Hero Member
  • *****
  • Join Date: Oct 2003
  • Posts: 1037
    • Show only replies by sir_inferno
Re: CF ide for Amiga1200 problem, Please help
« Reply #25 on: June 25, 2006, 04:25:38 PM »
Quote

PG wrote:
should work (but not in a master-slave chain)


hang on, surely if his miggy detects his IBM drive, he must have both connected...

and from what i understand ur saying that won't work...

emmm...

:/
Logged
 

Offline PG

  • Full Member
  • ***
  • Join Date: Feb 2004
  • Posts: 221
    • Show only replies by PG
Re: CF ide for Amiga1200 problem, Please help
« Reply #26 on: June 25, 2006, 05:02:24 PM »
And it doesnt...

Quote
In hdtoolbox didn't present the cf card as unknown or whatever. The hd toolbox find only my IBM 4.0GB hd.


The CF card is not detected.

I dont know his exact configuration there, but if you use a master slave-chain with the cf as master and a cd as slave, the CD-Rom will not work with most CF cards.
Logged
 

Offline bakoulisTopic starter

  • Full Member
  • ***
  • Join Date: May 2006
  • Posts: 170
    • Show only replies by bakoulis
Re: CF ide for Amiga1200 problem, Please help
« Reply #27 on: June 25, 2006, 05:49:35 PM »
When I used cf with idefix and hd, the hdtoolbox detect only my hd. When disconnected idefix board and hd and connected the cf to ide on motherboard, then booted from floppy and hdtoolbox wrote: "no hd devices connected" or something like that, I don't remember exactly. Probably my cards is not combatible.
________
CHEAP HERBAL VAPORIZERS
« Last Edit: May 02, 2011, 09:33:12 PM by bakoulis »
Logged
Amiga4000/18MB/040/LAN/RTG, Amiga1200HD/6MB, Amiga1200HD, Amiga3000/10MB/RTG, Amiga2000HD/17MB/030/LAN/RTG, Amiga1000/2.5MB, Amiga600/3MB, Amiga500/1MB 1.2, 2xAmiga500/1MB 1.3, Amiga500+/2MB, CDTV Expanded, CD32 Expanded.
 

Offline Chain

  • Hero Member
  • *****
  • Join Date: Jun 2005
  • Posts: 1324
    • Show only replies by Chain
    • http://chain.3dgrafika.cz/aktivity
Re: CF ide for Amiga1200 problem, Please help
« Reply #28 on: June 26, 2006, 05:58:45 AM »
Logged
too lazy to use shift key properly...
 

Offline bakoulisTopic starter

  • Full Member
  • ***
  • Join Date: May 2006
  • Posts: 170
    • Show only replies by bakoulis
Re: CF ide for Amiga1200 problem, Please help
« Reply #29 from previous page: June 26, 2006, 12:15:47 PM »
Quote

Chain wrote:
Maybe there is only problem as CF is not a REGULAR HDD...

http://home.freeuk.net/markk/Amiga_MO_FAQ/hdtoolbox_patch.html

(patched http://chain.3dgrafika.cz/amiga/hdtoolbox_cf.lha)


Thank you. I'll test it the next few days and I'll inform the forum for the result.

________
Hemp marijuana
« Last Edit: May 02, 2011, 09:33:21 PM by bakoulis »
Logged
Amiga4000/18MB/040/LAN/RTG, Amiga1200HD/6MB, Amiga1200HD, Amiga3000/10MB/RTG, Amiga2000HD/17MB/030/LAN/RTG, Amiga1000/2.5MB, Amiga600/3MB, Amiga500/1MB 1.2, 2xAmiga500/1MB 1.3, Amiga500+/2MB, CDTV Expanded, CD32 Expanded.
 
Pages: 1 [2] 3   Go Up
« previous next »