Setting up a Kupke Golem SCSI Controller A2000 *help*

[Daniele]

I have found a Golem SCSI for A2000 between my junk stuffs and wanted to see if it is working.

http://i36.tinypic.com/10d8b28.jpg

So I disconnected my SCSI HD from my beloved A2000 and hooked this Golem SCSI Controller. On http://amiga.resource.cx/exp/search.pl?amiga=2000&cat=scsi#golemscsi2000 I have fond the installation disk but when I run the floppy it seems to look for a fast1.device and even if I do scan in the main program no one HD is recognized! I have tried the HDToolBox of the WB2.0 and 3.1 but nothing to do!

How can I fix this?

The HD seems to have power bcoz it's spinning!

Thank you very much!

[Daniele]

@MozzerFan: Thanks... I know .sure..the scsi Card is turned "ON"

@orange: my Amiga start showing the KS screen and I do not have KS3.1 but KS2.0

What can I do?

[Daniele]

Soory, mind if I am asking... how can I change to scsi3.device? No devices are shown....

[Daniele]

@MozzerFan:

Hello Lloyd yes...if I edid scsi3.device I see something and many and 512K and if I see some options I see CYLs and something else but it is all German.... a real mass for me! What to do to Prep and Format?

Many Thanks

[Daniele]

Hello,

please I need more specific... I have copied fast1.device into devs of the Floppy Install of the WB2.1 ( the whole set is 5 disks)but when I load the HDToolBox no one device is showed. I tried to went on information on the menu into the WB to see the tooltype but nothing is written.
How to put scs3.device?

Now I am trying  HDInstTool by (Oliver Kastl) !

PLZ HLP!

[Daniele]

Hello Lloyd,

something happened: it appearas above STATUS -> Unsupported

What does it mean?

( anyway this Utility HDInstTool 6.9 by Oliver Kastl seems to be very kewl! )

Cheers!!! AMIGO!

[Daniele]

Well,

if I go over informations and see ToolTypes I see a "," before DEVICE=scsi3.device .
I removed the semicolon and started the HDTools ,made scan and can olnly see PIC 0 TID 6 LUN 0  STATUS Unsupported.

I tried this with a Quantum of 128 MB and an IBM 4,330 MB!

PS: What KS are you using. Here I am using KS2.0 but in the floppy install disk of this Card that I translated few minutes ago( that is all in German ) I read KS 1.3!!!

[Daniele]

Hi,

into the tooltypes there is DEVICE=scsi3.device and note SCSI_DEVICE_NAME=scsi3.device.


And Setup Drive is in grey....

What a pity...don't know what to do!

however I do not have words to express what I am for your kindness and willingness to help. thanks indeed!

[Daniele]

Almost fine,

we are make some little steps further ...
Even if the drives is marked as unknow I have the possibility to see some letters and Partition is not grey. But the problem is that if I try to define a new drive and read configurations from the drive it says that:

Drive does not support the SCSI Inquiry Command!

if I put some values and try to define the drive by myself what happen? All seems fine and it says that the HD is 20 MB. Maybe I was wrong when i told you it is 180MB and when I save the configuration I got an error and if I Exit it says that I would loose datas but after rebbot I cannot see any HD to format on my WB.

[Daniele]

Don't know what more can we do!

Do you think if I use the Install Floppy of the Card and KS1.3 I would fix it?

[Daniele]

I have just tried with the 4GB HD and the ToolBox give me the same errors of the Quantum. I see -3 error mosto of times. Maybe the Card is broken?

[Daniele]

Ok... I am going to find more information about the Quantum but what I wonder is that would be useless for the 4GB bcoz on the HD I have all the info and cannot be read by the HDToolBox!