Welcome, Guest. Please login or register.
Forums
« previous next »
Pages: [1]   Go Down

Author Topic: Amiga Explorer Issue  (Read 2112 times)

Description: Error reading from COM

0 Members and 1 Guest are viewing this topic.

Offline JurtappenTopic starter

  • Newbie
  • *
  • Join Date: Jan 2025
  • Posts: 8
  • Country: no
  • Gender: Male
    • Show only replies by Jurtappen
Amiga Explorer Issue
« on: February 05, 2025, 07:04:34 PM »
I am trying to setup the Amiga Explorer software with a null-mudem serial. Usb to serial from PC (CH340).
Getting the following error message: "error reading from COM". I get to the point were I type "RAM:Setup" on the Amiga.

I followed the instructions on how to set it up correctly.
Any idea where to start searching?

Cheers!
Logged
 

Offline AndyFC

Re: Amiga Explorer Issue
« Reply #1 on: February 05, 2025, 10:02:53 PM »
Hi, I use AExplorer over IP and used to use serial a long time ago.

There's a troubleshooting article here, and one of the points is about entering the ram:setup line correctly:
for example, entering "SER: to RAM:Setup" instead of "Type SER: to RAM:Setup"

https://www.amigaforever.com/kb/14-109

I hope it helps, sorry if you've already looked through it.
« Last Edit: February 05, 2025, 10:03:52 PM by AndyFC »
Logged
A1200 in DIY Tower. 3.2 ROMs (softkicking 3.2.3), OS 3.2.3, CF card, CD RW and IDE to SD adapter running off the internal IDE port (using the A4000 4-port IDE adapter from Amigakit), Pistorm 32 lite with Pi4/2GB/Emu68 or Blizzard 1230-IV, with 32MB 60ns RAM and 50MHz 68882 FPU.
MorphOS on PowerMac G5 and ATI 9600 pro
 

Offline JurtappenTopic starter

  • Newbie
  • *
  • Join Date: Jan 2025
  • Posts: 8
  • Country: no
  • Gender: Male
    • Show only replies by Jurtappen
Re: Amiga Explorer Issue
« Reply #2 on: February 06, 2025, 06:25:11 AM »
Thanks for the feedback👍 all info is good info. Anyway, it seems like it could be a null-modem cable problem. I also have to use a serial to USB adapter. The USB adapter has the designation CH340 and was bought from China somewhere 🙈 The cable was bought from Ebay and has both 9-pin and 25-pin options at each end. The problem occurs after getting to "RAM:Setup". The first communication "Type SER: to RAM:Setup" goes fine 🤔
Logged
 

Offline JurtappenTopic starter

  • Newbie
  • *
  • Join Date: Jan 2025
  • Posts: 8
  • Country: no
  • Gender: Male
    • Show only replies by Jurtappen
Re: Amiga Explorer Issue
« Reply #3 on: February 08, 2025, 05:45:31 PM »
Got my null modem cable from Ebay but it had the wrong wiring, so I pinched it up and made my own. Still the program seems to communicate only one way?

Are there any other settings that I can try to change?

Another thing to mention is that my USB to serial adapter has a CH340 chipset. Heard that adapter based on FTDI chipset is more reliable? Have also tried changing the COM port on the PC.
Logged
 

Offline JurtappenTopic starter

  • Newbie
  • *
  • Join Date: Jan 2025
  • Posts: 8
  • Country: no
  • Gender: Male
    • Show only replies by Jurtappen
Re: Amiga Explorer Issue
« Reply #4 on: February 23, 2025, 02:32:20 PM »
News update!

Ok, strangest thing;

I managed to get an old computer with onboard serial ports to run on windows 7 for leaving out the USB adapter question.
Installed Aexplorer on the computer and connected my home made null-modem cable in com2.
Started the setup wizard and same problem occured; "error opening com port 2" while at the last part on the Amiga "RAM:Setup"
I almost gave up on this but gave it a last shot; I just ran the setup wizard once more on the computer, still leaving the amiga in the "RAM:Setup" point. And voila!! It worked. Now I have Aexplorer on Amiga floppy.
I had to run the Setup Wizard twice ?!?

Any one that has a reasonable explanation to this ?

This case is solved  :)
Logged
 
Pages: [1]   Go Up
« previous next »