Welcome, Guest. Please login or register.
Forums
« previous next »
Pages: [1]   Go Down

Author Topic: Cybervision64 problem  (Read 941 times)

Description:

0 Members and 1 Guest are viewing this topic.

Offline FnacTopic starter

  • Newbie
  • *
  • Join Date: Apr 2003
  • Posts: 13
    • Show only replies by Fnac
Cybervision64 problem
« on: May 01, 2016, 07:22:22 PM »
Hello,

I have a A4000/040 revision b motherboard, and a cybervision64 video card.

I have the driver software installed (CX v4), and the problem is when computer boots it hangs with the cybergraphx logo. It never boots  to workbench.

I tried to change the zorro slot the card is installed but to no avail.

Any suggestions/ideias ??

Kind regards

Fnac
Logged
 

Offline Matt_H

Re: Cybervision64 problem
« Reply #1 on: May 02, 2016, 02:52:17 AM »
Hi, we need some more details. Did this start happening all of a sudden, i.e., it was working fine and then it wasn't? Or did you just install the card and the software for the first time and it's not working?

Go to the Early Startup Control menu (hold both mouse buttons while booting), and select Boot without Startup-Sequence. Then type:
set echo on
execute s:startup-sequence
You'll see the startup-sequence run line by line - where does it get stuck?
Logged
 

Offline roomeo

  • Newbie
  • *
  • Join Date: Nov 2009
  • Posts: 35
    • Show only replies by roomeo
Re: Cybervision64 problem
« Reply #2 on: May 02, 2016, 10:18:19 AM »
Quote from: Fnac;807785
Hello,

I have a A4000/040 revision b motherboard, and a cybervision64 video card.

I have the driver software installed (CX v4), and the problem is when computer boots it hangs with the cybergraphx logo. It never boots  to workbench.

I tried to change the zorro slot the card is installed but to no avail.

Any suggestions/ideias ??

Kind regards

Fnac


I experienced this while setting up a bvppc. It may be that the screenmode.prefs is still setup to open a pal screen. Hook a tv or monitor to your amiga, and select a cybergraphics screenmode and you will be set..

Took me a while to realize this myself...
Logged
a500 - Vampire500+
a600 - aca620/indiECS/Subway - Soon to be sold. :(
a4000 - 16mb Fast / Apollo4060@66mhz (ram not working) / X-Surf + RapidRoad / FastlaneZ3 64mb + Acard ARS-2000FU -> CfIDE / Delfina Lite / PicassoIV ... Who needs PCI?!
 

Offline Rotzloeffel

Re: Cybervision64 problem
« Reply #3 on: May 02, 2016, 11:51:35 AM »
Quote from: Fnac;807785
Hello,

I have the driver software installed (CX v4), and the problem is when computer boots it hangs with the cybergraphx logo. It never boots  to workbench.

That´s not the case! It just displays the original PAL-Mode on the RGB-Port! You have to connect a 15khz Monitor to you amiga and choose a Cybervision Screenmode before you can see the Workbench on the Cybervision :)
Logged
Save Planet Earth! It is the only one in the galaxy with fresh and cold beer :laughing:
 

Offline FnacTopic starter

  • Newbie
  • *
  • Join Date: Apr 2003
  • Posts: 13
    • Show only replies by Fnac
Re: Cybervision64 problem
« Reply #4 on: May 04, 2016, 07:56:14 PM »
Quote from: roomeo;807827
I experienced this while setting up a bvppc. It may be that the screenmode.prefs is still setup to open a pal screen. Hook a tv or monitor to your amiga, and select a cybergraphics screenmode and you will be set..

Took me a while to realize this myself...



That solved the problem! Thanks !!

I have been stuck on this problem for several days......
Logged
 
Pages: [1]   Go Up
« previous next »