Welcome, Guest. Please login or register.

Author Topic: Indivision AGA MK2 Failure?  (Read 2680 times)

Description:

0 Members and 1 Guest are viewing this topic.

Offline DarkXavierTopic starter

  • Newbie
  • *
  • Join Date: Jul 2009
  • Posts: 16
    • Show only replies by DarkXavier
Indivision AGA MK2 Failure?
« on: May 09, 2012, 09:09:38 AM »
Hi All,

I installed the indivision in my 1200 yesterday. Worked fine for about 2 hours connected via DVI and I also tried VGA, then had to go out so I switched the Amiga off. Later I thought I would try a DVI - HDMI cable as I want to use my pc monitor for my 1200, while having the pc connected by DVI. The cable didn't work so I tried the DVI cable, still nothing. So I tried a different monitor, not working with that either. Have tested the machine through RGB on my CM8833 and it works fine.

Any suggestions?

Thanks
 

Offline mousehouse

Re: Indivision AGA MK2 Failure?
« Reply #1 on: May 09, 2012, 09:43:38 AM »
I can only point out the obvious things... is it still seated properly or did it move slightly because of heating up and cooling down?

Other than that, maybe it's broken? There's no LED on it or anything to check it's working...
A3000T
 

Offline DarkXavierTopic starter

  • Newbie
  • *
  • Join Date: Jul 2009
  • Posts: 16
    • Show only replies by DarkXavier
Re: Indivision AGA MK2 Failure?
« Reply #2 on: May 09, 2012, 09:51:54 AM »
It's still seated fine. Looks like it is broken. :cry: Only trouble now is Amigakit's tech guy is off now until the 21St May.
 

Offline magnetic

  • Hero Member
  • *****
  • Join Date: Feb 2002
  • Posts: 2531
    • Show only replies by magnetic
Re: Indivision AGA MK2 Failure?
« Reply #3 on: May 09, 2012, 10:37:48 AM »
Well in this case any company with good support would just directly replace the board. I'm sure there is surplus and they must have a deal with Individual for failures... so the tech guy being on holiday shouldnt factor in imho.

Of course, that is indeed if the board is faulty.
bPlan Pegasos2 G4@1ghz
Quad Boot:Reg. MorphOS | OS4.1 U4 |Ubuntu GNU-Linux | MacOS X

Amiga 2000 Rom Switcher w/ 3.1 + 1.3 | HardFrame SCSI | CBM Ram board| A Squared LIVE! 2000 | Vlab Motion | Firecracker 24 gfx

Commodore CDTV: 68010 | ECS | 9mb Ram | SCSI -TV | 3.9 Rom | Developer EPROMs
 

Offline CritAnime

  • Previous Life Time Member
  • Hero Member
  • *****
  • Join Date: Jun 2011
  • Posts: 1143
    • Show only replies by CritAnime
Re: Indivision AGA MK2 Failure?
« Reply #4 on: May 09, 2012, 11:52:17 AM »
The seating meathod on these devices is similar to the accelerator I have in my 600. I had trouble initially with it even though it was seated right. So I removed the card and cleaned all the contacts on the cpu before reseating it. Maybe you could do the same with the chip that the indi sits on. Just use a bit of cleaning alcohol theb nake sure you seat theindi firmly after. It should make a lot of little clicks and creaks when seating.

Offline DarkXavierTopic starter

  • Newbie
  • *
  • Join Date: Jul 2009
  • Posts: 16
    • Show only replies by DarkXavier
Re: Indivision AGA MK2 Failure?
« Reply #5 on: May 09, 2012, 05:06:56 PM »
Quote from: CritAnime;692467
The seating meathod on these devices is similar to the accelerator I have in my 600. I had trouble initially with it even though it was seated right. So I removed the card and cleaned all the contacts on the cpu before reseating it. Maybe you could do the same with the chip that the indi sits on. Just use a bit of cleaning alcohol theb nake sure you seat theindi firmly after. It should make a lot of little clicks and creaks when seating.



Followed your advice and it now works again! Thanks! I feel like a idiot, should of thought of that. When it stopped working I just presumed the worst.
 

Offline bbond007

  • Hero Member
  • *****
  • Join Date: Mar 2009
  • Posts: 1517
    • Show only replies by bbond007
Re: Indivision AGA MK2 Failure?
« Reply #6 on: May 09, 2012, 05:19:51 PM »
Quote from: DarkXavier;692494
Followed your advice and it now works again! Thanks! I feel like a idiot, should of thought of that. When it stopped working I just presumed the worst.


It's also possible your 1200mb has a bad solder on the surface mount chip the Indivision fits on. That is more common with the A600 though.
 

Offline CritAnime

  • Previous Life Time Member
  • Hero Member
  • *****
  • Join Date: Jun 2011
  • Posts: 1143
    • Show only replies by CritAnime
Re: Indivision AGA MK2 Failure?
« Reply #7 on: May 09, 2012, 05:22:00 PM »
Quote from: DarkXavier;692494
Followed your advice and it now works again! Thanks! I feel like a idiot, should of thought of that. When it stopped working I just presumed the worst.


No probs. Glad it works again :)

Offline outlawal2

Re: Indivision AGA MK2 Failure?
« Reply #8 on: May 09, 2012, 07:49:07 PM »
Glad to hear it wasn't faulty.  I just ordered one yesterday!