EasyNet and NetGear Wireless MA401 *issue* please help!

[Framiga]

@Daniele


127.0.0.1 localhost
192.168.1.181 amiga


the router address in hosts, is redundant

and

Gateway Mode = Yes must be NO

PS- what a mess of configuration you got!

comment out that line also

;Use Name Server = First

[Daniele]

@Marcb: I renamed SSID as ROAD both in Router Settings and EasyNet Comfiguartion

@amije: If I ping the Amiga from the PC I have no one answer

@Framiga: you are right I fixed the redundancy now I have 192.168.181 as Amiga and 127.0.01 as loopback.


A little step further has been done by me only disablig the WEB Key Security.

If I connect the Amiga with the EasyNet to my router without any WEP Security I
can PING 192.168.1.1 and the routers send me all the packets but if
I ping www.amiga.org or www.google.com I see the name of the LAN I have given to
my windows XP and I have no answer.

Now that I renamed the SSIDD into router and EasyNet I cannot ping 192.168.1.1
anymore.

I don't know what is my fault into this configuration.
Since into my Router I have:

ON - Enable WEP Wireless Security

Encryption Key: 77 11 77 11 00 of 64 bit as HEX

Authentication Type:   Open Shared Both  
 
So I have tried into EasyNet to put the WEP key in this way ( 77 11 77 11 00 )
and I have a error 20 when I boot the Amiga) then tried the WEP Key as
7711-7711-00 Like it sees to suggest when I try to write into the field
but I cannot Ping 192.168.1.1 and same result I got if I write the WEP Key
in this way : 7711771100

My Questions are

1) What name is needed into EasyNet Network Domain Name?
2) How to communicate with the router with the WEP Key?
3) What to do to ping www.amiga.org or www.google.com or see these pages with AWeb Lite.

Thnaks and sorry to bother ya all!

[Framiga]

post here your AmiTCP:db/AmiTCP.config

There are other mistakes in your configuration here and there

[amigagr]

as i told you at pm, check the ascii ''on'' in the wep router settings and use a 5 characters password.
test for example the password 11111.

[Daniele]

@amije

hello,

as you can say in the picture I can only use 10 HEX decimal digit for 64 Key Bit.

Let me Know and Thanks You Very Much!!!

[amigagr]

what other options gives you at authentication type? is it give you a ''shared key''? if yes, use it.

[Daniele]

@Framiga,

Dear Mate here we go:

AmiTCP:db/AmiTCP.config

useloopback=YES
debugsana=YES
usens=FIRST
gateway=NO
MBUF_CONF MAXMEM=256
logfilename=ram:t/EasyNet.log
consolename=NIL:

EasyNet Debug Log:

HOSTNAME:
amiga
AMITCP port found
add host amiga: gateway localhost
add host loopback: gateway 127.0.0.1: File exists
add net default: gateway 192.168.1.1
bsdsocket.library 3.28

EasyNet Debug Log:

++ EasyNet Information ++

Version            = $VER: EasyNet 0.168 (14/06/08) AmigaKit.com
bsdsocket.library  = 3.28


++ Network Settings ++

Your IP address    = 192.168.1.181
Network SubNetMask = 255.255.255.0
Router/Gateway IP  = 192.168.1.1
Your hostname      = amiga
Network domainname = amiga


++ Domain Name Servers ++

Primary DNS        = 212.216.112.112
Secondary DNS      = 212.216.172.62
Tertiary DNS       =


++ Network Interface ++  

Device             = prism2.device (unknown version installed)
Unit Number        = 0
Wireless Settings  = C:SetPrism2Defaults SSID ROAD KEY 7711771100 (version 0.4 installed)
Library            = pccard.library (unknown version installed)


++ TCPIP Settings ++  

MBUF_CONF MAXMEM   = 256K
Use Name Server    = First
Use Loopback       = Yes
Debug SANA         = Yes
Gateway Mode       = No


++ Hosts ++  

192.168.1.181      amiga  amiga
192.168.1.1        router  
127.0.0.1          loopback  


++ Assigns ++  

Assign AmiTCP: "WORK:AmiTCP"


Hope we can fix everything!!!!

[ncafferkey]

You mustn't comment out SetPrism2Defaults from your startup scripts. This is how the wireless settings get set, so you can't use WEP otherwise. If it's giving you an error, try running it in the shell after you boot as a test. Make sure it's in C: too.

Also, don't use shared key authentication; prism2.device doesn't support it. And does your card not support 128-bit WEP?

[Daniele]

Hello,

it happens that I have to put ; evertime I change setting beacause actually I don't know how to write correctly the WEP key into EasyNet:

77 11 77 11 00 or

7711-7711-00          like the field seems ti suggest or

7711771100

it happens that when I write 7711771100 when I reboot I have an error into CLI. But after that I comment the wireless start-up and make all the EasyNet Setting by scratch I save the configuration.

Actually I am making this attemps using 2 different routers and the one who is working when I disable the WEP KEY has only a 128 bit WEP KEY.


What can I do with the SetPrism2Defaults command if I have return code 20 when I boot the amiga?

Many Thanks Guys!!!

[ncafferkey]

Daniele wrote:

What can I do with the SetPrism2Defaults command if I have return code 20 when I boot the amiga?

ncafferkey wrote:

If it's giving you an error, try running it in the shell after you boot as a test. Make sure it's in C: too.

[Daniele]

If I configure the Wep Key in this way : C:SetPrism2Defaults SSID ROAD KEY 7711771100

I do not have any error in the boot but I neither can manage to Ping 192.168.1.1 nor see any Web page with IBrowse.

Only without Wep Key I manage to have one answer ant the Ping 192.168.1.1 only. Nothing to do to see any web pages form the IBrowse.