Welcome, Guest. Please login or register.

Author Topic: Preformated HD wont work boot on Warp Engine scsi?  (Read 2026 times)

Description:

0 Members and 1 Guest are viewing this topic.

Offline sarkisTopic starter

  • Jr. Member
  • **
  • Join Date: Apr 2002
  • Posts: 95
    • Show all replies
Preformated HD wont work boot on Warp Engine scsi?
« on: January 04, 2003, 10:24:14 AM »
Have a 3000d with Warp Engine 4040  :-D
but :-?
the system has but one scsi HD that was formated with hdtool box before the Warp Engine arrived..
How can the HD be now on the Warp Engine scsi
controller..
 :-?
thinkin ;-)
say get another scsi hd..leave the booting hd
on the 3000's internal controller and format the new scsi hd on the warp engine controller but how?
RTFM! dont have the manual  :-(
GOT the install disk tho  8-)
TIA :-D  :-D  :-D  :-D
SARKIS
 

Offline sarkisTopic starter

  • Jr. Member
  • **
  • Join Date: Apr 2002
  • Posts: 95
    • Show all replies
Re: Preformated HD wont work boot on Warp Engine scsi?
« Reply #1 on: January 04, 2003, 03:18:49 PM »
Thx for the post  :-D
Its a 4040 and it has 4 simm slots..
Yep soldered the cable init2
Blasted a hole where the floppy drive was!


matt3k wrote:


. .



JP1: SCSI Termination Power.
ON!
JP2: A Mode Select - Off: 040 Active On: 040 disabled.   OFF!!!
           B:  SIMM Bank Size - Off:Dual Sided.  On Single Sided.  ON!!!!!!!
            C: SIMM Size - Off 16MB On 4Mb  OFF!!!!!
             D:  Wait State - Off: no wait state On: Wait State.  ON!!!!!! NOT SURE OF SPEED OF SIMMS
              E. Reserved.
              F: MMU disable- Off: MMU enable on: MMU Disabled.  OFF!!!!
              G: Cache diasable Off: Caches enabled.
                                          OFF!!!!!!!!

              H: SCSI config jumper  ON!!!
              J: SCSI config jumper   ON!!!
               K: SCSI config jumper.  ON!!!

********************************************************
               L: Reserved ON.  This is off ????
does the manual say it 's to be """"ON''''''''?????

dont have the manual
*********************************************************

JP3 Reserved.
JP4 Wire Clip for a3000 Version.[/quote]  :-P
 

Offline sarkisTopic starter

  • Jr. Member
  • **
  • Join Date: Apr 2002
  • Posts: 95
    • Show all replies
Re: Preformated HD wont work boot on Warp Engine scsi?
« Reply #2 on: January 04, 2003, 11:07:50 PM »
thx MATT3K,,,,,,,, :-o  ;-)  8-)  :-x

that last jumper made the warp engine come to life!!!!!!  8-)  8-)  8-)  8-)  8-)
i had it set to off and it messed up the warp engine and my 3000D  :-(
now its reading almost all the memory and no gurus...
i live in Boston is it possible to send a copy of the manual..
whats on your amiga wish list?
sarkisssimon@netscape.net
 

Offline sarkisTopic starter

  • Jr. Member
  • **
  • Join Date: Apr 2002
  • Posts: 95
    • Show all replies
Re: Preformated HD wont work boot on Warp Engine scsi?
« Reply #3 on: January 05, 2003, 08:20:26 PM »
Heading on Ebay for some 32 meg simms and a barracuda scsi for the warp engine
thx again
sarkis :-D  :-D  :-D  :-D