Any Linux experts here?

[bilko9070]

Im having several troubles with Suse 10.0(evaluation edition).

The one which is really bugging me is that i cant get my speedtouch 330 usb modem to work.

The device is listed as `active` in the detailed hardware scan, but i cant get any internet activity out of it..

I have configured the `dsl` panal and entered isp username etc.

Any ideas helpfull people? :-o

[bilko9070]

On my XP network panal, when the modems connected it says.

Server Type: PPP
Transports:  TCP/IP

I did set it up as PPPoATM  , which i believe is correct.

[bilko9070]

PPPoA is what i ment i think....

This is from the isp website..

VPI SETTING    0 (zero)
VCI SETTING    38
CONNECTION PIPE    Relates to the part of your ADSL login after the @ symbol as specified on your Account Card e.g. lon1-aj1e.demonadsl.co.uk
PROTOCOL TYPE OR ENCAPSULATION METHOD    PPPoA (also known as RFC2364 in some equipment)
AUTHENTICATION TYPE    CHAP
TRAFFIC TYPE    UBR
FRAMING OR MULTIPLEXING METHOD    VC/MUX
MODE ITU    G.dmt
DIAL UP NUMBER    Some modems may require you to enter 0,38 (or 0 as the area code and 38 as the number)
IP ADDRESS/RANGE    As specified on your Account Card

[bilko9070]

I know i could get a router but however, im poor and determined.......

Can i ask, why would downgrading work?  If i try to install suse 9.1 i just end up having to disable my sata device before liunx will do anything, which 10.0 does not seem to mind.. :-x

[bilko9070]

Right!
I would imagine that the USB modem has its drivers etc loaded ok because both green lights are on which usually means the hardware is active.
The device shows up correctly under the USB device monitor as well.
So, thats the driver side of things i assume to be ok.

I am using the DSL network setup in YaST.

I have four options...

PPP over ATM
PPP over Eithernet
CAPI for ADSL
Point to Point Tunneling Protocall.

I would assume that the only one which applies to me is `PPP over ATM`, because that is the only one which gives me the option to enter the VPI/VCI (0.38).

Here is the connection log for it.
*********************************
SuSE Meta pppd (smpppd-ifcfg), Version 1.59 on linux.
Status is: disconnected
trying to connect to smpppd
connect to smpppd
Status is: disconnected
Status is: lurking
pppd[0]: Plugin pppoatm.so loaded.
pppd[0]: PPPoATM plugin_init
pppd[0]: Plugin passwordfd.so loaded.
pppd[0]: PPPoATM setdevname_pppoatm - SUCCESS:0.38
pppd[0]: Renamed interface ppp0 to dsl0
pppd[0]: Using interface dsl0
Status is: lurking
pppd[0]: Couldn't increase MTU to 1500
pppd[0]: Couldn't set up demand-dialled PPP interface: Inappropriate ioctl for device
Status is: disconnected
Status is: disconnecting
pppd[0] died: Fatal pppd error (exit code 1)
****************************************


It looks like the other options are only for a connectin via router because they give me network card setup options etc but i am using a USB modem.
Just in case it gives any clues i have included the logs for attempts via the other options.......

************************************
CAPI for ADSL

SuSE Meta pppd (smpppd-ifcfg), Version 1.59 on linux.
Status is: disconnected
trying to connect to smpppd
connect to smpppd
Status is: disconnected
Status is: lurking
pppd[0]: Plugin capiplugin.so loaded.
pppd[0]: capiplugin: $Revision: 1.36 $
pppd[0]: capiconn:  1.13
pppd[0]: capiplugin: CAPI_REGISTER failed - CAPI not installed (0x1009) [No such file or directory (2)]
Status is: disconnected
pppd[0] died: Fatal pppd error (exit code 1)
************************************************

************************************************
PPP over Eithernet

SuSE Meta pppd (smpppd-ifcfg), Version 1.59 on linux.
Status is: disconnected
trying to connect to smpppd
connect to smpppd
Status is: disconnected
Interface is eth0.
Status is: lurking
pppd[0]: Plugin rp-pppoe.so loaded.
pppd[0]: RP-PPPoE plugin version 3.3 compiled against pppd 2.4.3
pppd[0]: Plugin passwordfd.so loaded.
pppd[0]: Renamed interface ppp0 to dsl0
pppd[0]: Using interface dsl0
Status is: lurking
pppd[0]: Couldn't increase MTU to 1500
pppd[0]: Couldn't increase MRU to 1500
pppd[0]: local  IP address 192.168.99.1
pppd[0]: remote IP address 192.168.99.99
pppd[0]: Starting link
Establishing connection due to activity.
Status is: connecting
pppd[0]: Timeout waiting for PADO packets
Timeout Waiting for PADO packets. Check your setup and cables and try again.
pppd[0]: Unable to complete PPPoE Discovery
pppd[0]: Starting link
Establishing connection due to activity.
Status is: connecting
pppd[0]: Timeout waiting for PADO packets
Timeout Waiting for PADO packets. Check your setup and cables and try again.
pppd[0]: Unable to complete PPPoE Discovery
pppd[0]: Starting link
Establishing connection due to activity.
Status is: connecting
pppd[0]: Timeout waiting for PADO packets
Timeout Waiting for PADO packets. Check your setup and cables and try again.
pppd[0]: Unable to complete PPPoE Discovery
********************************************


********************************************
Point to Point tunneling protocall.

SuSE Meta pppd (smpppd-ifcfg), Version 1.59 on linux.
Status is: disconnected
trying to connect to smpppd
connect to smpppd
Status is: disconnected
Status is: lurking
pppd[0]: Plugin passwordfd.so loaded.
pppd[0]: Renamed interface ppp0 to dsl0
pppd[0]: Using interface dsl0
Status is: lurking
pppd[0]: local  IP address 192.168.99.1
pppd[0]: remote IP address 192.168.99.99
pppd[0]: Starting link
Establishing connection due to activity.
Status is: connecting
pppd[0]: Serial connection established.
pppd[0]: Connect: dsl0 <--> /dev/pts/0
****************************************




I am now considering getting a router as they are cheap and people rekon that they are easier to get working.  I dont see why they are easier tho because i dont really understand how they work.  Could someone explain how easy it would be to get the connection working if i had a router?

[bilko9070]

Ok, i have had a small result!
I found this script.
http://steve-parker.org/speedtouchconf/

It runs then fails at the last part.  I will contact the author of the script but i thought id print a log incase anyone here might know what is going on!

*****************************************************

linux:~ # cd /root/Desktop/speedtouchconf-2.0-25_Nov_2005
linux:~/Desktop/speedtouchconf-2.0-25_Nov_2005 # ./speedtouchconf.sh
(c) Steve Parker, 17 Oct 2002 - 2005 (http://steve-parker.org)
speedtouchconf comes with ABSOLUTELY NO WARRANTY; for details type:
    ./speedtouchconf.sh -gpl
This is free software, and you are welcome to redistribute it
under certain conditions.
See the included file COPYING for more details.

************************************************
*                                              *
*       speedtouchconf.sh by Steve Parker      *
*                                              *
*    http://speedtouchconf.sourceforge.net/    *
* based on speedtouch.sourceforge.net project  *
*                                              *
************************************************

If you have any problems with this script, mail me
(steve at steve-parker dot org) with the files
/tmp/speedtouch.txt and /var/log/messages for diagnosis.
  Linux kernel version 2.6 okay.
/root/Desktop/speedtouchconf-2.0-25_Nov_2005
*******************************************
*                                         *
*     Please select your ISP Settings     *
*                                         *
*******************************************

  Country/ISP            VPI    VCI
  Belgium, ?              8     35
  Denmark, Orang          8     35
  France, wanado          8     35
  France, ?               8     67
  Italy, ?                8     35
  Netherlands, ?          8     48
  Netherlands             0     35
  Poland (NeoStrada)      0     35
  UK, Any                 0     38
  Austria (AON)           8     48
  US, BellSouth           8     35
  Singapore Pacificnet    0    100
Please type your VPI VCI numbers (eg, 0 38 for UK)
0 38
Please enter your ISP Login ID (eg another@hg1.btinternet.com)
*********@home500.dslaccess.co.uk
Please enter your ISP Password
*******
Settings:
  VPI / VCI : 0 / 38
  Login     : **********@home500.dslaccess.co.uk
  Password  : *******
Are these correct? (Y/N)
y
No further user interaction is required.
Configuring SpeedTouch Driver...
Software Configuration - SUCCESS
Building SpeedTouch Driver...
Software Build - SUCCESS
Installing SpeedTouch Driver...
Software Installation - SUCCESS
Creating ppp files in /etc/ppp
You can ignore any insmod hints here...

   *** Configuration finished. Starting the connection ***

Sat Jan  7 10:02:18 GMT 2006
The modem lights should start flashing for approx. 60 seconds...
You might see some messages about USBDEVFS_BULK failed - you can ignore this.
Sat Jan  7 10:02:18 GMT 2006
The modem_run command failed (code 235)
modem_run results:
Mutex value not OK
FAILED because of modem_run error 235
linux:~/Desktop/speedtouchconf-2.0-25_Nov_2005 #

******************************************************

[bilko9070]

motorollin wrote:
Try this or this

--
moto

WOW!  Thanks for that MOTO!
Im now typing this from SUSE 10.0!  
I think this was the magic part "add the word "speedtch" to the end of the blacklist".

Now to have fun with linux all day!
:-D  :-o  :-)  ;-)