CyberstormPPC weirdness

[gdanko]

Good news and bad. I found a CyberstormPPC in the 3000T I picked up last night. Bad news is, the Amiga will not boot with it in place.

The manual for the card mentions these jumpers need to be set as such:
BRDCLK (J102) - Ext
CPUCLK (J104) - Int
QUADCLK (J100) - Ext

According to some documentation I've found, these settings are...
BRDCLK - Jump 1&2
CPUCLK - Jump 1&2
QUADCLK - Jump 3&4
With these settings the 3000 won't boot after I've installed the card. As with the 2000 the power light starts dim then brightens shortly after you power on. With these jumper settings and the CyberstormPPC card installed the power light stays dim. The fan spins and everything else powers up. But no kickstart screen or anything.

Now, if I put the jumpers back to normal:
BRDCLK - Jump 2&3
CPUCLK - Jump 1&2
QUADCLK - Jump 1&2
and remove the CyberstormPPC the system boots right up.

Has anyone here had any experience with this card and a 3000T? I would really LOVE to use it.

[gdanko]

Tahoe wrote:
If i'm not mistaken, I believe CPUCLCK (J104) should be set to ext also...

Can you check your jumper settings for me and let me know? I thought it should be as well but the PDF manual online says it needs to be INT??

Should the card snap in place? It seems pretty easy to remove... so I wonder if I am not seating it well enough.

[gdanko]

billchase wrote:
Reseat the card.  The cyberstorms wiggle in the cpu slot very
easily.  The slightest misalignment will prevent it from
booting.

C Snyder

That is what I am wondering. It pulls out pretty easily.. How do I know it is in place? It does not click or snap in when I push it. I can see the two white plastic rods through the holes though.

[gdanko]

Framiga wrote:
hello gdanko

do you have some RAM installed on CSPPC?

Yes I have two SIMMs in slots 1 and 3, which appears to be Bank 1. I guess the configuration is:
Bank 1: 1 & 3
Bank 2: 2 & 4

Are you using the A3KT internal SCSI2 controller?

I've unplugged all hard disks and only tried the floppy.

Can you get the CSPPC EarlyBootMenu? (click on ESC during the boot)

I believe I've tried this with no luck.

Ah . . . if you have nothing attached to the CSPPC UWSCSI controller, try to click on the "s" key during the boot (this disable the UWSCSI controller)

I will try both of these now.

Post some more info about software/hw config

i.e its a CSPPC with 060 . . 040? do you have the 68K libs installed?

When I boot into the system with nothing else installed I have 2MB chip RAM and 8MB fast RAM.
It has Workbench 40.68 (3.1)
Everything else looks stock.
As for the CSPPC? Let's see...
I do not know if it is an 060 or 040.
There are two crystals labeled "SCO-060 66.000MHz 97-12" and "3X0-22C 50.000MHz C C"

I will post a photo of it shortly.

I have not yet installed the libs. I want to see if I can even get the boot menu. But like I said.. The typical pattern is. The power light starts dim then goes bright as it starts to boot. With the CSPPC in place it stays dim. Not getting to the disk yet.

[gdanko]

Well, the CyberstormPPC is now functional. I re-seated the 68k chip, verified the jumpers, and re-inserted the card.

One thing I am confused with is this. When I look at the system info the CPU is reported as a 68040. First of all, didn't the 604e/233 ship with a 68060? The crystal on the board seems to indicate it is an '060. Also, how do I tell if the PowerPC is present? I would like to check that out.

Thanks for all the input.

[gdanko]

My A2000 with a Blizzard 2060 reports a 68060

[gdanko]

And I ran the Phase5 install disk
And I looked in the Libs dir
And I see 68060.library, 68040.library, and 68040new.library
And I am using the same app to check the stats on both systems with the same OS version

I may very well have an 040 Cyberstorm Which is OK by me.