Warp3d ramlib error ppc task error???????help!!

[tolishot]

please help!!on war3d ppctask shows ramlib error,ppc task error!i have install new os3.9 with ward3d latest and warpos
and i put on ppc 603e the bvppc vga card.i change the rasolution in 8bit 15bit and 24bit to test gearsppc test tool.
the same message: ramlib error....ppc task error!what is mean   this message?i have problem with ppc cpu?the memory speed on ppc menu is 70ns.i try and 60ns.the same!!help me please!!!  :cry:  :cry:  :boohoo:  :boohoo:

[tolishot]

with this two patch we solved this problem?sure?the warp3d tools gears ppc and other progs like demos w3d ppc dosent work from begining to buy the amiga ppc accelerator! :getmad:  :getmad:

[tolishot]

look the memory speed on ppc configuration menu if you setting is 60ns then do 70ns and try again.
my problem is when runs warp3d progs or demos.i try to install one of the patches mcp13..lha.setting of angel tools of mmu
tryiningto run demoskope runs onces.then after that dont runs again i dont know whats happens!help? :getmad:  :getmad:

[tolishot]

hmmmm!i have all the latest progs warp3d warpos cgfx.i dont try to set the 16bit resolution.but this problem i dont understund why the resolution of my bzvppc is only 320x480 to 800x600?and tell me if it ok this on warpos test tool voxelrace on cgfx 320x480 is 67hz?in runing!tell me is ok the speed?
something else:the steps to setup from begining the bvppc card to show the resolution in screenmodes!thanks! :getmad:  :getmad:

[tolishot]

look!i dont know if my ppc 603e had problem but if it is problem why some programs runs?like warpos? like warptest warp gears68k? warp engine shows  in 320x280 about 65 fps!it is ok?

[tolishot]

gears 68k works fine but slow.
gears 68k window dont run .
gearsppc white screen or exception page ppc task error.
gearsppc window. the same.
glsokoban the same.
engine works fine with good fps.
when he calls ppc task is the problem.then exception page.
i am confused.sorry !!
but i tryning to fix this problem.i loose my mind in this amiga.if it something is wrong i cant see!new configuration!latest programs with updates!i cant solved the problem!!!!! :madashell:  :madashell:  :madashell:  :pissed:

[tolishot]

your video address is correct?check your bvppc is the same video address?i have the same settings too! :-D

[tolishot]

in my voxelspace in full screen 320x240 8bit gives about 68-70 hz.:)on me work engine, gears68k,and warptest.i push my ppc on 266mhz and 68040 in 30 mhz.i put ram in 50-60ns.and the config menu on ppc is 60ns the ram. :rtfm:

[tolishot]

maybe is memory the problem?
?
wrong settings in configuration menu on ppc?
post the congiguration menu ppc here to compare the chenges!thanks!

[tolishot]

hmm!me too!also!the 2 memory 2x128mb in 60ns the 1200 crashes!
in 70ns worked fine!tell me if you know doctorq:the free config is better?or kneeds some settings? :rtfm:

[tolishot]

the settings of the ppc bios on me dose not shows all of them.
only two settings is availiable!
nomaprom and
no 31khz default screen.all the others is in the shadow.
any ideas?? :-?

[tolishot]

yes i have install all latest!
my ppc is phase 5 no dce!