Elbox Mediator 1200 LT4 PCI locking up

[Lurch]

Ahh yes the joys of the Mediator. RTG Voodoo goodness so close yet so far.

After reinstalling/uninstalling drivers over and over I have admitted defeat :-/

1) I can get it to detect the the Voodoo card and even the SB128 card. PCIINFO shows both.

2) After following the instructions the voodoo modes are showing and I can select between them but when I save it locks up.

3) I've tried using the updated pci library.

I am using an ATX to AT adapter to power the mediator (and the A1200 through the mediator). Doing this with a 300W ATX PSU.

It's a v1.0 going by what is on it, I've been told it was working fine with the same Voodoo card.

Have read a few posts but no real solution :-/

[Lurch]

I've set the jumpers:

8MB / CONFIG ON / WAIT ON.

Have emailed Elbox so will post here any updates.

[Lurch]

LOL at the moment it's all sitting naked on the desk but yes. Apollo 060, other mods are in my sig.

Have it all fitting nicely together even with the indivision :-)

With the Mediator it doesn't fit in my custom case so will need to look for a full tower, not a midi which is a shame :-/

Will have another go this afternoon.

[Lurch]

Sadly Ive had no luck getting this to work. Just end up getting lock ups when I try switching to the the voodoo card screen modes.

Swapping the card to different slots also doesnt help. PCIINFO shows that it has detected the card but still no joy.

Have tried the another voodoo card and same result so will assume its not the card.

Picked up a 5 volt ATI 9200 boots okay with it but doesnt detect the card properly unknown device when I run PCIINFO.

Anyway one more shot tomorrow night then it all goes into a box and Ill be on selling.

Maybe get a brand new mediator, expensive lesson :-/

[Lurch]

Cheers guys, have tried the above.

When in Picasso96 mode and I click edit it locks and I have to reboot.

When I tried installing nlist I had a runtime error and had to reboot, the other applications installed fine.

If I use the AHI that comes with the original MMCD disk (not sure what version) I get a runtime when opening it's preferences.

I've set the jumpers to 8MB / CONFIG ON / WAIT OFF as a re read of the manual suggests Wait should be off.

Is something conflicting with my Apollo 060?

If I remove the Mediator I dont get software errors in the apps I've tried. Of course anything related to the Mediator doesn't work as it's not installed.

Guessing I'll have to start from scratch again :-(

[Lurch]

Hmm, I have the coloured dots and a couple of stickers. So assume these are updated chips?

So it's 13 Pounds for a new set? I've emailed Elbox a couple of times no reply. One for registration and one for support.

Most likely because I bought it second hand.

Thinking I'll return it and buy a brand new one :-(

Kind of over it at the moment, although the person I bought off said he had it working with the same cards he sent with it so not sure.

[Lurch]

Okay so I reseated the mach chips, and now I either get software error when I click on screenmodes or recoverable errors when selecting a Voodoo mode.

A question, how warm/hot do the mach chips get?

[Lurch]

I appreciate the help so far :-)

It's a 300W ATX CPU and the 5V seems fine, the apollo 060 runs rock solid at 80MHz.

The A1200 has had timing fixes and caps replaced by Amigakit, had to do this for the ACA1231 to work.

I've checked the pass through connector it appears to be okay, can't see anything weird going on and the contacts on the A1200 look good, gave it a quick clean.

Not sure about cleaning the pass through connector though.

I've tried it with just the Voodoo card on it's own in various slots. I haven't even attempted to get the sound working. It does detect the SB128 and it shows in AHI but no sound.

No hiss/click on boot either, will have another look at the pass through :-/

[Lurch]

One thing I have noticed with the MACH chips is that if I push them entirely into their sockets (they make a click noise) the Amiga wont boot.

I have to raise them flat with the top of the sockets for the Amiga to boot, don't know if that means anything?

[Lurch]

Haven't heard anything and I've had it a couple of weeks now. So not sure what's happening there.

Going to give it a look over on the weekend.

[Lurch]

Looks like a brand new Mediator now but still no luck. I was reading somewhere it could be because I'm also using a Subway? (A political stand off or something?)

Is this the case?

Have run out of time tonight but will try removing the Subway and see how that goes, but that seems weird when I've seen people using a Mediator with a Subway.

Stay tuned.

[Lurch]

My Amiga curse. Would be nice if somethings would just work.

Have left it alone today, shouldn't be this hard?

Feel bad asking to return it.

[Lurch]

I had a Subway working together with Mediator TX and they co-existed nicely.

On the edge of my seat as to wether I should purchase a SX/TX through Amigakit as the cost is a bit more.

But I do have a Radeon 9200 sitting here that I would like to use, and no clear yes/no if it would work with the LT4.

Also with the SX/TX I hear you can connect a standard ATX power switch straight to it? If so this will also be a plus :-)

[Lurch]

Hmmm, could this be the needle in the haystack? Showed up under the camera.

[Lurch]

Ended up buying a brand new one from Amigakit. Worked straight out of the box :-)