Amiga.org

Amigakit Hardware => A600GS & A1200NG => Topic started by: SkulleateR on April 14, 2025, 06:05:07 PM

Title: Resetting System/Programs/Work to built in defaults does nothing
Post by: SkulleateR on April 14, 2025, 06:05:07 PM

Just have weird problems with AmiBench so I wanted to reset it ... Doing this does nothing, the files are all the same and I still got the gfx issue like described here : https://forum.amiga.org/index.php?topic=76910.0

Title: Re: Resetting System/Programs/Work to built in defaults does nothing
Post by: broadblues on April 14, 2025, 08:31:16 PM

If you have a older image, this  may not work.

The issue you reference can more easily be fixed by going to the  advanced update section and choosing to reinstall  system.lhapps

Title: Re: Resetting System/Programs/Work to built in defaults does nothing
Post by: SkulleateR on April 14, 2025, 11:00:32 PM

Quote from: broadblues on April 14, 2025, 08:31:16 PM

If you have a older image, this  may not work.

The issue you reference can more easily be fixed by going to the  advanced update section and choosing to reinstall  system.lhapps

Tried that, did not work either ... Currently I´m stuck ... I had not touched AmiBench since last update to find out it won´t work anymore. Then tried to reinstall the update, won´t work, then tried SystemV46 back to factory, won´t work ... so I have a non working system now :(

Title: Re: Resetting System/Programs/Work to built in defaults does nothing
Post by: broadblues on April 15, 2025, 10:27:05 AM

Try reinstalling the a600gs.deb as well.

I've not yet seen this issue, a few others have had it and fresh update has usually fixed it.

Title: Re: Resetting System/Programs/Work to built in defaults does nothing
Post by: SkulleateR on April 15, 2025, 11:16:15 AM

Quote from: broadblues on April 15, 2025, 10:27:05 AM

Try reinstalling the a600gs.deb as well.

I've not yet seen this issue, a few others have had it and fresh update has usually fixed it.

Been through that this morning, changes nothing ... AmiBench only loads up a shell as LoadWB isn´t executed and that's it ! Of course I got an SD card backup but that also means I´m loosing all my save states and setups I created so I will only take this route when there´s no other way out of it  >:(

Title: Re: Resetting System/Programs/Work to built in defaults does nothing
Post by: broadblues on April 15, 2025, 11:42:18 AM

Um check your partitions boot pris in the EDIT section for AmiBench

HD0: SsyemV46 should be 0
DH0: DH0: should be 1

Others should be -127

if these re wrong it will not boot properly and end up in the stub installation.

Send me screen shot be for trying reinstalling  applications.lhapps

Title: Re: Resetting System/Programs/Work to built in defaults does nothing
Post by: SkulleateR on April 16, 2025, 02:22:50 PM

Quote from: broadblues on April 15, 2025, 11:42:18 AM

Um check your partitions boot pris in the EDIT section for AmiBench

HD0: SsyemV46 should be 0
DH0: DH0: should be 1

Others should be -127

if these re wrong it will not boot properly and end up in the stub installation.

No, they are correct, already checked that. Meanwhile I tried copying back a manual backup of SystemV46 by using DOpus4 and there are some files that cannot be found but they are definitely on there ... I think my SD card got corrupted. I´ll try cloning it and do the advanced update again after.

Title: Re: Resetting System/Programs/Work to built in defaults does nothing
Post by: SkulleateR on April 17, 2025, 06:15:35 PM

I can confirm : the SD card that came with the A600GS is corrupt ...

I cloned it onto a new 64GB Sandisk and made the complete Update on it and have no more errors, everything is working fine. After that I tried to write an image file on the defective one and ... nope, not working at all, not even a format works.