Amiga.org
Amiga computer related discussion => Amiga Hardware Issues and discussion => Topic started by: Sutty100 on November 29, 2011, 10:44:58 PM
-
I bought a home made flicker fixer scan doubler off ebay and have a few issues which I wondered if anybody else has had? First workbench does not look great lines scanning across and the image "wobbles". In games the image is good but only takes up the top part of the screen leaving around a third of the bottom blank. This is with an amiga 1200, Over the weekend I am going to test it with an amiga 500 and a tv with VGA in. Should I try and get a refund or are flicker fixers generaly not perfect? Really dissapointed being as this cost £100 and I was expecting great things!!
-
Indivison AGA Mrk2 (http://eab.abime.net/showthread.php?t=55980) should be out in a couple of weeks, I'd just wait for that if I were you....
-
Pics, link?
-
All my flickerfixers work perfectly.
-
btw: AGA machines require 24 bit flicker fixers, older models will limit you to 4096 colors.
A decent FF is near perfect. The only problem to expect is ghosting with rapid movement (in interlaced modes).
-
I did take a video of it on my phone but it is not the best quality and quite hard to tell the crap quality of the camera from the crap quality of the flicker fixer!
http://www.youtube.com/watch?v=KieoAz5_J_w
There are lines going diagonally across the screen they go one way for a while then reverse direction. It defiantly isn't near perfect! He has agreed to do a return but I have still wasted £10 on p+p :(
-
I had a similar problem with mine, the sceen would freeze but the 5% of the top screen would work. I wast do to the converter nor supporting the PAL resolution. In your case it may not supprt your current video resolution.
Try to change the Amiga resolution to NTSC or PAL which ever you are not using and see if the problem goes away.
do you cave close up or model number of the ff?
-
I had a similar problem with mine, the sceen would freeze but the 5% of the top screen would work. I wast do to the converter nor supporting the PAL resolution. In your case it may not supprt your current video resolution.
Try to change the Amiga resolution to NTSC or PAL which ever you are not using and see if the problem goes away.
do you cave close up or model number of the ff?
I tried all available resolutions in workbench but to no avail. It doesn't have a model number or anything like that on it... should of been a sign! The link to it is below:
http://www.ebay.co.uk/itm/280778703151?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
I would strongly advise avoiding it!
-
Your FF is based on this one: GBS-8220
http://www.ebay.co.uk/itm/Arcade-game-RGB-CGA-EGA-YUV-VGA-HD-video-converter-board-1-VGA-output-/250893072432?pt=LH_DefaultDomain_3&hash=item3a6a647830
I have the same one, and it works OK in NTSC mode for me, but the PAL is giving me problems, the Flicker fixer is actually good on this one, in interlace mode the screen is rock solid.
There are some people in this forum that say it works good for them, maybe you have a dud.
-
I tried all available resolutions in workbench but to no avail. It doesn't have a model number or anything like that on it... should of been a sign! The link to it is below:
http://www.ebay.co.uk/itm/280778703151?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
I would strongly advise avoiding it!
Looks like the refresh rate is really low too.
-
Hi,
Part of your problem is power related. There is a limit, maybe 0.5A maximum on the +5V supply from the port. A GBS-8220 requires 2.0 Amps at 5V.
Are you using a higher wattage power supply? An A500 PSU that can source 4.5A (check label underneath) or a modified AT/ATX PSU is ideal.
Did you get the refund agreed?
Ian
-
All my flickerfixers work perfectly.
OK, now try playing SlamTilt in interlaced mode and report back :)
-
OK, now try playing SlamTilt in interlaced mode and report back :)
I played SlamTilt a lot waaaaaaaaaaaay back but I don't remember it being in interlace?
But I was probably playing it on a different computer anyway.
How would I force SlamTilt into interlace mode?
-
I played SlamTilt a lot waaaaaaaaaaaay back but I don't remember it being in interlace?
But I was probably playing it on a different computer anyway.
How would I force SlamTilt into interlace mode?
It changes into hires interlaced whenever there are more than one ball.
-
If think Stedy is on the right track - on what I can make out it looks like a power/grounding issue.
-
I was using a 500 PSU I do have a 1200 one so I will try that later to see if it helps although being as he advertised this for use with a 500 you would expect it to work!
-
I'm so glad I didn't buy that - I was really tempted until I realised I can buy the same hardware for $35, uncased. I might buy that.
I bought another so-called scandoubler off eBay a month ago, and it's so terrible it's going back:
http://www.ebay.com.au/itm/15Khz-RGB-RGsB-RGBS-VGA-XGA-Converter-Scaler-/350497862833?pt=LH_DefaultDomain_0&hash=item519b4cf4b1
It's advertised as crystal clear conversion for a lot of systems including Amiga, but it truly is a pile of crap. Pronounced vertical lines, artifacts, and no hardware adjustment either. Expensive to post back to the US too - $30. The unit is apparently set for EGA only, according to the technical people at the company in California. Any kind of search for "Amiga VGA" on eBay will bring up their crappy product. It's blatent misrepresentation.