Amiga.org
Amiga computer related discussion => Amiga Hardware Issues and discussion => Topic started by: alewis on November 07, 2006, 10:45:09 PM
-
Resurrected my A1200 tower jobbie with a view to finally finishing the project off.
I've had this combo for, oh, 7 years now. Its been booted up perhaps twice in that time... (so I know it works!)
Essentially an A1200, Blizzard 1260 c/w SCSI, RBM On-board ISA/ZII expander, Eyetech EZ-key, and some other odds and sods.
Easy starts for 10
A1200 HD interface: Is Pin 1 *really* Pin 1? (looking at the 1200 top down, floppy drive to the right, P1 is towards the bottom of the case, ie nearer the space bar than the rear expansion ports)
The 4 vacant pins on the 44/40 cable adaptor, do they cover the l/h side (pin 1 edge) or r/h side (pin 44) edge? Reason being is no HD is recognised, I get the "insert disk" screen
Maybe easy... What key combination on a PC keyboard equals CTRL-Amiga-Amiga? I remember when I had an A1200 in the early 90's and fitted a 3.5" HD it needed a soft reboot to be recognised. Wondering if that is the problem here, I cant seem to soft reset. I might have booted it thsi way years ago, but that would have been using an AT keyboard, I'm using a PS/2 via a PS/2-AT adaptor into the EZ-Key...
Bit harder. The system tries to boot. it goes through grey, dark grey, sometimes sticks on black, sometimes goes dark grey after black, and sometimes makes it as far as the purple insert disk screen. Any ideas? For troubleshooting I've removed the SCSI+RAM module (and the On-board), and am running with a 4MB 60ns SIMM, maprom enabled or disabled makes no discernable difference.
Bit trickier. Once on boot up it got as far as a guru error. Another time it got as far as displaying - briefly - a multicoloured flashing bar screen. Words fail, the best I can describe is, as being similar to the flashing bars common on packed executable when they decrunched. This was with the HD fitted, so *might* be something on that, but its been that long I dont remember what was in the startup-sequence... Wondering if it is the Blizzard doing something.
There are a few other areas - I cant recall getting the PCMCIA ethernet going, this was an Amiga branded kit, cant remember details/vendor, but is anyone aware of an issue with PCMCIA NICs and Blizzards/accelerators in general? But I'll leave them until I get the basic box going....
Help! (and apologies to those who have read at eab)
-
Hi,
See http://www.eyetech.co.uk/SUPPORT/SGUIDE/BUFFE002.HTM ref info about pin 1 on the A1200 IDE header.
The colours, a cascade effect is a Bus Test which the A1260 carries out, mine does that, tis normal.
Ensure you have installed the latest ver Libraries you will need 4,
My Libs
68040.library ver 46.5
68040new.library ver 46.5
68040.old.library ver 37.30
68060.library ver 46.7
yes you will need the 040 libs as well.
I'm sorry. but, I dont have a URL for the libs, if you need them please PM me and I'll E-Mail them to you.
Also, check you have installed your SCSI Tools and run them.
Ref the PCMCIA NIC see http://aminet.net/search.php?query=PCMCIA
CardPatch.lha 1.2 util/boot 3K 2003-07-13 m68k-amigaos Patches bugs in PCMCIA system V1.2 - (readme) CardReset.lha
util/boot 3K 2002-08-17 m68k-amigaos Forces reset signal on PCMCIA slot V3.0 - (readme)
3c589.lha 1.4 hard/drivr 54K 2004-03-23 m68k-amigaos Driver for 3Com PCMCIA network cards - (readme)
cnetdevice-1.9beta1.lha 1.9beta hard/drivr 180K 2006-09-06 m68k-amigaos PCMCIA Network Card driver - (readme)
cnetdevice.lha 1.8b hard/drivr 146K 2002-11-06 m68k-amigaos PCMCIA Network Card driver. V1.8b - (readme)
Kind Regards, Michael
aka rockape
-
your problem seems like the one I had: the Blizzard does not make good contact eventhough it's fitted as it should. Try this: Keep lightly pressed the board while booting. Try both directions. To make it more clear, let's say u had your miggy in a desktop and you had the top of it removed and the trapdoor open. You should try to press lightly the board towards the desk at first before booting and kep it there during the boot process - that's what worked for me, if it doesn't, try pulling it towards the ceiling. I know all that sound scrambled, but I can't find a better way to describe it. If u need further assistance with it, pm me. But remember: press only lightly.