X5000 Failing to Boot OS4!

[Acill]

I've had my X5000 working great for quite a while now. After being turned off for several weeks it no longer boots anything. It will power up and show the initial X5000 screen, the boing ball will spin and it will then turn to a gray screen and sit. If I do nothing it will reset itself and repeat back to the X5000 logo. I can interrupt the boing ball and get into u-boot and interact just fine. If I load OS4 from u-boot menu It shows "Loading finished ######################### 100%" message comes up after a short time. The next Line reads: "About to call loader entry at 0x7BD02020" at which point it just hangs there.

NO media will boot into OS4. The original CD, my recovery USB stick, or the SSD in it with OD4 installed. The last time I used my system it was fine. I didn't make any changes to it. It's sat and now doesn't work.

The odd thing, if I put in the other GPU I have that supports MorphOS and connect the 2nd SSD I have with a clean install of MorphOS on it, it boots fine into that. SO... This is something OS4 related it seems that came up from nowhere. I now have my system back to stock and am still trying to get it to boot into OS4.

[Acill]

System is as basic as it can be, still failing to boot from anything with OS4 on it.

[Acill]

This is the serial output

2 USB Device(s) found
SATA0 (3 Gbps)
U-Boot 2014.04 (Oct 17 2016 - 08:22:22)
CE at device
CPU0:  P5020, Version: 2.0, (0x82200020)
Core:  e5500, Version: 1.2, (0x80240012)
Clock Configuration:
       CPU0:1995 MHz, CPU1:1995 MHz,
       CCB:798  MHz,
       DDR:665  MHz (1330 MT/s data rate) (Asynchronous), LBC:49.875 MHz
       FMAN1: 498.750 MHz
       QMAN:  399 MHz
       PME:   399 MHz
L1:    D-cache 32 KiB enabled
       I-cache 32 KiB enabled
Reset Configuration Word (RCW):-ST Prod.: DVDRAM GH24NSC0 Rev: LI00
       00000000: 0c540000 00000000 1e1e0000 00000000
       00000010: 44808c00 ff002000 68000000 45000000
       00000020: 00000000 00000000 00000000 0003000f
       00000030: a0000000 00000000 00000000 00000000
Board: CYRUS
36-bit Addressing
I2C:   ready
SPI:   ready
DRAM:  Initializing....using SPD
DDR: failed to read SPD from address 81
Detected UDIMM VS2GB1333D3
There is no rank on CS0 for controller 0.
Not enough bank(chip-select) for CS0+CS1 on controller 0, interleaving disabled!
Not enough bank(chip-select) for CS0+CS1 on controller 1, interleaving disabled!
Not all DIMMs are identical. Memory controller interleaving disabled.
2 GiB (DDR3, 64-bit, CL=9, ECC off)

Local Bus Controller Registers
BR0     0xE0001001      OR0     0xFFF00010
BR1     0xE1001001      OR1     0xFFF00010
BR2     0x00000000      OR2     0x00000000
BR3     0x00000000      OR3     0x00000000
BR4     0x00000000      OR4     0x00000000
BR5     0x00000000      OR5     0x00000000
BR6     0x00000000      OR6     0x00000000
BR7     0x00000000      OR7     0x00000000
LBCR    0x40000000      LCRR    0x80010004
L2:    512 KiB enabled
Corenet Platform Cache: 2 MiB enabled
SERDES: bank 2 disabled
MMC:  FSL_SDHC: 0
EEPROM: NXID v0
PCIe1: Root Complex, x4 gen2, regs @ 0xfe200000
  01:00.0     - 1002:683d - Display controller
  01:00.1     - 1002:aab0 - Multimedia device
PCIe1: Bus 00 - 01
PCIe2: Root Complex, x4 gen2, regs @ 0xfe201000
  03:00.0     - 111d:8092 - Bridge device
   04:01.0    - 111d:8092 - Bridge device
    05:00.0   - 12d8:e111 - Bridge device
   04:02.0    - 111d:8092 - Bridge device
    07:00.0   - 10ec:8168 - Network controller
   04:03.0    - 111d:8092 - Bridge device
   04:08.0    - 111d:8092 - Bridge device
   04:10.0    - 111d:8092 - Bridge device
PCIe2: Bus 02 - 0a
PCIe3: disabled
PCIe4: disabled
Looking for VGA
PINS: 0xfc000808
videoboot: Booting PCI video card bus 1, function 0, device 0
Begin BIOS POST
End BIOS POST
Setting VESA Mode
Found required VESA mode
About to set mode 279
About to get mode
Got mode 49431 (0xc117)
OK
XSize = 1024 YSize = 768 Base =0xe0000000
mmio_base = 0x80000000
bgx = 0xad55ad55 fgx = 0x0
In:    serial
Out:   serial
Err:   serial
ID: NXID v0
SN: 116330024
UID: 4429431001910050e4d4a080a0800000
Errata: ÿÿÿÿÿBGÿ
Build date: 2015/06/11 14:42:47
CRC: 3d2fd346
SCSI:  scanning bus for devices...
Found 0 device(s).
Net:   Initializing Fman

MMC read: dev # 0, block # 1130, count 128 ...
Fman1: Uploading microcode version 106.1.0
Tuning PHY @ 3
Tuning PHY @ 7
FM1@DTSEC4 [PRIME], FM1@DTSEC5

MMC read: dev # 0, block # 1280, count 512 ... 512 blocks read: OK

MMC read: dev # 0, block # 65536, count 131072 ... 131072 blocks read: OK
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
USB1:   USB EHCI 1.00
scanning bus 1 for devices... 2 USB Device(s) found
SATA0 (3 Gbps)
       SATA1 (1.5 Gbps)
CE at device
scanning bus for devices...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
  Device 0: (1:0) Vendor: HL-DT-ST Prod.: DVDRAM GH24NSC0 Rev: LI00
            Type: Removable CD ROM
            Capacity: not available
Found 1 device(s).
## Starting application at 0x00200000 ...


Loading finished             [########################################] 100 %
About to call loader entry at 0x7BD02020

[Acill]

Tried a new battery, nothing.

Saw the  DDR sticks showing as not the same, which isn't accurate so I replaced them with another set. The original set was in first, then the newer set. Same issue with loading, but they both reported the same. Tried with just one stick and no change.

U-Boot 2014.04 (Oct 17 2016 - 08:22:22)

CPU0:  P5020, Version: 2.0, (0x82200020)
Core:  e5500, Version: 1.2, (0x80240012)
Clock Configuration:
       CPU0:1995 MHz, CPU1:1995 MHz,
       CCB:798  MHz,
       DDR:665  MHz (1330 MT/s data rate) (Asynchronous), LBC:49.875 MHz
       FMAN1: 498.750 MHz
       QMAN:  399 MHz
       PME:   399 MHz
L1:    D-cache 32 KiB enabled
       I-cache 32 KiB enabled
Reset Configuration Word (RCW):
       00000000: 0c540000 00000000 1e1e0000 00000000
       00000010: 44808c00 ff002000 68000000 45000000
       00000020: 00000000 00000000 00000000 0003000f
       00000030: a0000000 00000000 00000000 00000000
Board: CYRUS
36-bit Addressing
I2C:   ready
SPI:   ready
DRAM:  Initializing....using SPD
DDR: failed to read SPD from address 81
Detected UDIMM KHX1600C10D3/8G
There is no rank on CS0 for controller 0.
Not enough bank(chip-select) for CS0+CS1 on controller 0, interleaving disabled!
Not all DIMMs are identical. Memory controller interleaving disabled.
6 GiB left unmapped
8 GiB (DDR3, 64-bit, CL=9, ECC off)
       DDR Chip-Select Interleaving Mode: CS0+CS1

Local Bus Controller Registers
BR0     0xE0001001      OR0     0xFFF00010
BR1     0xE1001001      OR1     0xFFF00010
BR2     0x00000000      OR2     0x00000000
BR3     0x00000000      OR3     0x00000000
BR4     0x00000000      OR4     0x00000000
BR5     0x00000000      OR5     0x00000000
BR6     0x00000000      OR6     0x00000000
BR7     0x00000000      OR7     0x00000000
LBCR    0x40000000      LCRR    0x80010004
L2:    512 KiB enabled
Corenet Platform Cache: 2 MiB enabled
SERDES: bank 2 disabled
MMC:  FSL_SDHC: 0
EEPROM: NXID v0
PCIe1: Root Complex, x4 gen2, regs @ 0xfe200000
  01:00.0     - 1002:683d - Display controller
  01:00.1     - 1002:aab0 - Multimedia device
PCIe1: Bus 00 - 01
PCIe2: Root Complex, x4 gen2, regs @ 0xfe201000
  03:00.0     - 111d:8092 - Bridge device
   04:01.0    - 111d:8092 - Bridge device
    05:00.0   - 12d8:e111 - Bridge device
   04:02.0    - 111d:8092 - Bridge device
    07:00.0   - 10ec:8168 - Network controller
   04:03.0    - 111d:8092 - Bridge device
   04:08.0    - 111d:8092 - Bridge device
   04:10.0    - 111d:8092 - Bridge device
PCIe2: Bus 02 - 0a
PCIe3: disabled
PCIe4: disabled
Looking for VGA
PINS: 0xfc000808
videoboot: Booting PCI video card bus 1, function 0, device 0
Begin BIOS POST
End BIOS POST
Setting VESA Mode
Found required VESA mode
About to set mode 279
About to get mode
Got mode 49431 (0xc117)
OK
XSize = 1024 YSize = 768 Base =0xe0000000
mmio_base = 0x80000000
bgx = 0xad55ad55 fgx = 0x0
In:    serial
Out:   serial
Err:   serial
ID: NXID v0
SN: 116330024
UID: 4429431001910050e4d4a080a0800000
Errata: ÿÿÿÿÿBGÿ
Build date: 2015/06/11 14:42:47
CRC: 3d2fd346
SCSI:  scanning bus for devices...
Found 0 device(s).
Net:   Initializing Fman

MMC read: dev # 0, block # 1130, count 128 ...
Fman1: Uploading microcode version 106.1.0
Tuning PHY @ 3
Tuning PHY @ 7
FM1@DTSEC4 [PRIME], FM1@DTSEC5

MMC read: dev # 0, block # 1280, count 512 ... 512 blocks read: OK

MMC read: dev # 0, block # 65536, count 131072 ... 131072 blocks read: OK
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
USB1:   USB EHCI 1.00
scanning bus 1 for devices... 2 USB Device(s) found
SATA0 (3 Gbps)
       SATA1 (1.5 Gbps)
CE at device
scanning bus for devices...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
  Device 0: (1:0) Vendor: HL-DT-ST Prod.: DVDRAM GH24NSC0 Rev: LI00
            Type: Removable CD ROM
            Capacity: not available
Found 1 device(s).
## Starting application at 0x00200000 ...


Loading finished             [########################################] 100 %
About to call loader entry at 0x7BD02020

[Acill]

I have posted it there and the other forums, lol. Im now at the point of giving up. I honestly hate this thing now.

[Acill]

I have been messaging Matthew from Amigakit multiple times with no reply back. I am fed up with this machine now and don't want to deal with it any longer.

[Acill]

Yup, doesnt matter what I use.

[Acill]

U-Boot variables from serial out

X5000> printenv
amigaboot_quiet=Y
amigabootmenu_default=0
baudrate=115200
bdev=sda3
bootargs=root=/dev/sda2 mem=3500M console=ttyS0,115200 console=tty0
bootargs_live=root=/dev/ramdisk boot=casper mem=3500M ro --
bootargs_live_debug=root=/dev/ramdisk boot=casper mem=3500M ro break debug
bootcmd=setenv bootargs root=/dev/$bdev rw console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
bootdelay=10
bootdvd=scsi reset ; load scsi 0 2000000 boot_dvd ; bootm 2000000
bootfile=uImage
consoledev=ttyS0
eth1addr=00:80:10:11:07:08
ethact=FM1@DTSEC4
ethaddr=00:80:10:11:07:07
ethernetboot=echo Running Ethernet Boot
ethprime=FM1@DTSEC4
fdtaddr=c00000
fman_ucode=7fe733f0
harddiskboot=echo Running Hard Disk Boot
hwconfig=fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1;usb1:dr_mode=host,phy_type=utmi;usb2:dr_mode=host,phy_type=utmi
linuxboot=echo Running Linux
liveusb=usb start ; setenv bootargs_live_debug ; ext2load usb 1:1 2000000 boot_dvd ; bootm 2000000
loadaddr=1000000
loadbmps=mmc read 0x10005000 0x500 0x200; mmc read 0x20000000 0x10000 0x20000
massboot=usb reset ; boota
mos=bootmorphos
netdev=eth0
nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
opticalboot=echo Running Optical Boot
preboot=run loadbmps;bmp d 0x20000000;ami
ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr $ramdiskaddr $fdtaddr
ramdiskaddr=2000000
ramdiskfile=ramdisk.uboot
rootpath=/opt/nfsroot
scsidevs=1
stdin=usbkbd,serial
stdout=serial,vga
uboot=u-boot.bin
ubootaddr=0xFFF80000

Environment size: 1917/8188 bytes

[Acill]

PAcking it up!

[Acill]

Thanks for all the reply in this.

As for the RAM issue. I noticed that and posted the 2nd serial log because it was reading the RAM bad or something I though in the first. I am not mixing RAM and they are in pairs. The first set is a pair of 2GB sticks from Corsair that the machine shipped with. The other is a pair of HyperX 8GB that was working perfectly before all this and was recommended and tested from AOTL for X5000 use.

The USB devices installed are only the keyboard and mouse. The other stuff its showing is the internal USB headers and ports. Nothing USB is connected.

I have tried with my DVD out, HDD out, USB stick in upper slot, CD install disk, all are the same result as this.

I have used new SATA cables, changed ports, no change.

I have replaced the CR22 coin cell with a new one that I measured the voltage on and was a good 3.4V

I tried a new HDD and it wont boot from USB or CD to get to the point of installing as mentioned, so no good.

I have tried with three different video cards. #1 it shipped new with was a R250X (7750) #2 is a HD6950, #3 was the primary card id been using with the newer enhancer 2.0 beta and drivers and is a 560. I know the last card wont boot from the CD and work, buiut the other two should, and #1 has several times before. I have restored my system a few times in the past from CD and USB.

As I mentioned, I can replace the GPU with the 6950 and put in my MorphOS HDD and it boots into it perfectly, so its SOMETHING to do with OS4.1 or something in U-Boot that magicly change while powered off for the last couple weeks I was gone on work trips that's caused this.

I got fed up and packed it away, so no idea what to do, and A-eon isn't really helping much. Trevor asked me to do a lot of what you all said, and its not changed anything.

[Acill]

For now I am giving up. Since all boot media fails I am more in line to thinking its the video driver not compatible, but I have booted from the CD before to restore as well as this USB drive so not sure what the deal is.

[Acill]

5450? Will this one work? It was cheap enough to get it and take a chance.

https://www.amazon.com/Diamond-Multimedia-Express-Graphics-5450PE31G/dp/B006MBP7R2/ref=pd_lpo_147_t_1/140-1138464-8662800?_encoding=UTF8&pd_rd_i=B006MBP7R2&pd_rd_r=1a1b9129-f315-4a03-91ac-56810885d957&pd_rd_w=qgtPe&pd_rd_wg=hsrFE&pf_rd_p=7b36d496-f366-4631-94d3-61b87b52511b&pf_rd_r=PRDCK9DMDDAHA6FNQYGZ&psc=1&refRID=PRDCK9DMDDAHA6FNQYGZ

[Acill]

Do you have an image of this USB boot stick I can try?My question is why have I been able to boot from CD and USB in the past if I had to restore but now I cant? Its something odd happening.

[Acill]

So once again, by pure magic, it works again. I did nothing other than had it off for a couple of days. I just got my Radeon 5450 in and tried it, booted right up. Put my Polaris 11 card in again, booted right up. I just don't understand this machine sometimes?!

I am not joking, I did nothing other than power it off a couple of days, swap cards (keeping in mind I had been swapping cards before the 5450 came in), and Poof, it works.

[Acill]

You joke, but its been on since last boot, lol!