Amiga.org
Amiga computer related discussion => Amiga Hardware Issues and discussion => Topic started by: Acill on December 26, 2020, 05:05:07 PM
-
I've had my X5000 working great for quite a while now. After being turned off for several weeks it no longer boots anything. It will power up and show the initial X5000 screen, the boing ball will spin and it will then turn to a gray screen and sit. If I do nothing it will reset itself and repeat back to the X5000 logo. I can interrupt the boing ball and get into u-boot and interact just fine. If I load OS4 from u-boot menu It shows "Loading finished ######################### 100%" message comes up after a short time. The next Line reads: "About to call loader entry at 0x7BD02020" at which point it just hangs there.
NO media will boot into OS4. The original CD, my recovery USB stick, or the SSD in it with OD4 installed. The last time I used my system it was fine. I didn't make any changes to it. It's sat and now doesn't work.
The odd thing, if I put in the other GPU I have that supports MorphOS and connect the 2nd SSD I have with a clean install of MorphOS on it, it boots fine into that. SO... This is something OS4 related it seems that came up from nowhere. I now have my system back to stock and am still trying to get it to boot into OS4.
-
Happy Holidays Paul! From your troubleshooting so far it sounds like the GPU or your primary SSD / primary SSD connection. With your OS4 GPU in place, are you disconnecting the primary SSD when you try to boot OS4 from CD or USB? Just a thought... ;) Also, do you have anything plugged into the special “Xorro” slot?
-
System is as basic as it can be, still failing to boot from anything with OS4 on it.
-
This is the serial output
2 USB Device(s) found
SATA0 (3 Gbps)
U-Boot 2014.04 (Oct 17 2016 - 08:22:22)
CE at device
CPU0: P5020, Version: 2.0, (0x82200020)
Core: e5500, Version: 1.2, (0x80240012)
Clock Configuration:
CPU0:1995 MHz, CPU1:1995 MHz,
CCB:798 MHz,
DDR:665 MHz (1330 MT/s data rate) (Asynchronous), LBC:49.875 MHz
FMAN1: 498.750 MHz
QMAN: 399 MHz
PME: 399 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
Reset Configuration Word (RCW):-ST Prod.: DVDRAM GH24NSC0 Rev: LI00
00000000: 0c540000 00000000 1e1e0000 00000000
00000010: 44808c00 ff002000 68000000 45000000
00000020: 00000000 00000000 00000000 0003000f
00000030: a0000000 00000000 00000000 00000000
Board: CYRUS
36-bit Addressing
I2C: ready
SPI: ready
DRAM: Initializing....using SPD
DDR: failed to read SPD from address 81
Detected UDIMM VS2GB1333D3
There is no rank on CS0 for controller 0.
Not enough bank(chip-select) for CS0+CS1 on controller 0, interleaving disabled!
Not enough bank(chip-select) for CS0+CS1 on controller 1, interleaving disabled!
Not all DIMMs are identical. Memory controller interleaving disabled.
2 GiB (DDR3, 64-bit, CL=9, ECC off)
Local Bus Controller Registers
BR0 0xE0001001 OR0 0xFFF00010
BR1 0xE1001001 OR1 0xFFF00010
BR2 0x00000000 OR2 0x00000000
BR3 0x00000000 OR3 0x00000000
BR4 0x00000000 OR4 0x00000000
BR5 0x00000000 OR5 0x00000000
BR6 0x00000000 OR6 0x00000000
BR7 0x00000000 OR7 0x00000000
LBCR 0x40000000 LCRR 0x80010004
L2: 512 KiB enabled
Corenet Platform Cache: 2 MiB enabled
SERDES: bank 2 disabled
MMC: FSL_SDHC: 0
EEPROM: NXID v0
PCIe1: Root Complex, x4 gen2, regs @ 0xfe200000
01:00.0 - 1002:683d - Display controller
01:00.1 - 1002:aab0 - Multimedia device
PCIe1: Bus 00 - 01
PCIe2: Root Complex, x4 gen2, regs @ 0xfe201000
03:00.0 - 111d:8092 - Bridge device
04:01.0 - 111d:8092 - Bridge device
05:00.0 - 12d8:e111 - Bridge device
04:02.0 - 111d:8092 - Bridge device
07:00.0 - 10ec:8168 - Network controller
04:03.0 - 111d:8092 - Bridge device
04:08.0 - 111d:8092 - Bridge device
04:10.0 - 111d:8092 - Bridge device
PCIe2: Bus 02 - 0a
PCIe3: disabled
PCIe4: disabled
Looking for VGA
PINS: 0xfc000808
videoboot: Booting PCI video card bus 1, function 0, device 0
Begin BIOS POST
End BIOS POST
Setting VESA Mode
Found required VESA mode
About to set mode 279
About to get mode
Got mode 49431 (0xc117)
OK
XSize = 1024 YSize = 768 Base =0xe0000000
mmio_base = 0x80000000
bgx = 0xad55ad55 fgx = 0x0
In: serial
Out: serial
Err: serial
ID: NXID v0
SN: 116330024
UID: 4429431001910050e4d4a080a0800000
Errata: ÿÿÿÿÿBGÿ
Build date: 2015/06/11 14:42:47
CRC: 3d2fd346
SCSI: scanning bus for devices...
Found 0 device(s).
Net: Initializing Fman
MMC read: dev # 0, block # 1130, count 128 ...
Fman1: Uploading microcode version 106.1.0
Tuning PHY @ 3
Tuning PHY @ 7
FM1@DTSEC4 [PRIME], FM1@DTSEC5
MMC read: dev # 0, block # 1280, count 512 ... 512 blocks read: OK
MMC read: dev # 0, block # 65536, count 131072 ... 131072 blocks read: OK
USB0: USB EHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 2 USB Device(s) found
SATA0 (3 Gbps)
SATA1 (1.5 Gbps)
CE at device
scanning bus for devices...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Device 0: (1:0) Vendor: HL-DT-ST Prod.: DVDRAM GH24NSC0 Rev: LI00
Type: Removable CD ROM
Capacity: not available
Found 1 device(s).
## Starting application at 0x00200000 ...
Loading finished [########################################] 100 %
About to call loader entry at 0x7BD02020
-
Hmmm, must be RAM related. I'm sure you've swapped out RAM? Swapped current RAM modules to check for a RAM failure at a different address?
-
hey Paul I had the same thing happen with my X1000 a year ago and I swapped the CR2032 CMOS battery on the MB and all great....hope this solves your X5000 problem too !
If that doesn't help chekc out the Hyperion support forum (https://forum.hyperion-entertainment.com/ (https://forum.hyperion-entertainment.com/))
-
Tried a new battery, nothing.
Saw the DDR sticks showing as not the same, which isn't accurate so I replaced them with another set. The original set was in first, then the newer set. Same issue with loading, but they both reported the same. Tried with just one stick and no change.
U-Boot 2014.04 (Oct 17 2016 - 08:22:22)
CPU0: P5020, Version: 2.0, (0x82200020)
Core: e5500, Version: 1.2, (0x80240012)
Clock Configuration:
CPU0:1995 MHz, CPU1:1995 MHz,
CCB:798 MHz,
DDR:665 MHz (1330 MT/s data rate) (Asynchronous), LBC:49.875 MHz
FMAN1: 498.750 MHz
QMAN: 399 MHz
PME: 399 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
Reset Configuration Word (RCW):
00000000: 0c540000 00000000 1e1e0000 00000000
00000010: 44808c00 ff002000 68000000 45000000
00000020: 00000000 00000000 00000000 0003000f
00000030: a0000000 00000000 00000000 00000000
Board: CYRUS
36-bit Addressing
I2C: ready
SPI: ready
DRAM: Initializing....using SPD
DDR: failed to read SPD from address 81
Detected UDIMM KHX1600C10D3/8G
There is no rank on CS0 for controller 0.
Not enough bank(chip-select) for CS0+CS1 on controller 0, interleaving disabled!
Not all DIMMs are identical. Memory controller interleaving disabled.
6 GiB left unmapped
8 GiB (DDR3, 64-bit, CL=9, ECC off)
DDR Chip-Select Interleaving Mode: CS0+CS1
Local Bus Controller Registers
BR0 0xE0001001 OR0 0xFFF00010
BR1 0xE1001001 OR1 0xFFF00010
BR2 0x00000000 OR2 0x00000000
BR3 0x00000000 OR3 0x00000000
BR4 0x00000000 OR4 0x00000000
BR5 0x00000000 OR5 0x00000000
BR6 0x00000000 OR6 0x00000000
BR7 0x00000000 OR7 0x00000000
LBCR 0x40000000 LCRR 0x80010004
L2: 512 KiB enabled
Corenet Platform Cache: 2 MiB enabled
SERDES: bank 2 disabled
MMC: FSL_SDHC: 0
EEPROM: NXID v0
PCIe1: Root Complex, x4 gen2, regs @ 0xfe200000
01:00.0 - 1002:683d - Display controller
01:00.1 - 1002:aab0 - Multimedia device
PCIe1: Bus 00 - 01
PCIe2: Root Complex, x4 gen2, regs @ 0xfe201000
03:00.0 - 111d:8092 - Bridge device
04:01.0 - 111d:8092 - Bridge device
05:00.0 - 12d8:e111 - Bridge device
04:02.0 - 111d:8092 - Bridge device
07:00.0 - 10ec:8168 - Network controller
04:03.0 - 111d:8092 - Bridge device
04:08.0 - 111d:8092 - Bridge device
04:10.0 - 111d:8092 - Bridge device
PCIe2: Bus 02 - 0a
PCIe3: disabled
PCIe4: disabled
Looking for VGA
PINS: 0xfc000808
videoboot: Booting PCI video card bus 1, function 0, device 0
Begin BIOS POST
End BIOS POST
Setting VESA Mode
Found required VESA mode
About to set mode 279
About to get mode
Got mode 49431 (0xc117)
OK
XSize = 1024 YSize = 768 Base =0xe0000000
mmio_base = 0x80000000
bgx = 0xad55ad55 fgx = 0x0
In: serial
Out: serial
Err: serial
ID: NXID v0
SN: 116330024
UID: 4429431001910050e4d4a080a0800000
Errata: ÿÿÿÿÿBGÿ
Build date: 2015/06/11 14:42:47
CRC: 3d2fd346
SCSI: scanning bus for devices...
Found 0 device(s).
Net: Initializing Fman
MMC read: dev # 0, block # 1130, count 128 ...
Fman1: Uploading microcode version 106.1.0
Tuning PHY @ 3
Tuning PHY @ 7
FM1@DTSEC4 [PRIME], FM1@DTSEC5
MMC read: dev # 0, block # 1280, count 512 ... 512 blocks read: OK
MMC read: dev # 0, block # 65536, count 131072 ... 131072 blocks read: OK
USB0: USB EHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 2 USB Device(s) found
SATA0 (3 Gbps)
SATA1 (1.5 Gbps)
CE at device
scanning bus for devices...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Device 0: (1:0) Vendor: HL-DT-ST Prod.: DVDRAM GH24NSC0 Rev: LI00
Type: Removable CD ROM
Capacity: not available
Found 1 device(s).
## Starting application at 0x00200000 ...
Loading finished [########################################] 100 %
About to call loader entry at 0x7BD02020
-
ah sorry to hear that...I was gonna say to try only 1 Ram stick but you tried that too...did you try posting this on Hyperion forum as they have a dedicated X5000 section
-
I have posted it there and the other forums, lol. Im now at the point of giving up. I honestly hate this thing now.
-
I have posted it there and the other forums, lol. Im now at the point of giving up. I honestly hate this thing now.
now you sound like me and my 1200 Tower...talk about love/hate relationships over the years ;D ..stick with it as your X5000 is still being produced today which is a rariity nowadays so at worst even if it is a MB defect you can send it back to A-Eon to get repaired or if still under warranty they'll send you a new one
-
I have been messaging Matthew from Amigakit multiple times with no reply back. I am fed up with this machine now and don't want to deal with it any longer.
-
I have been messaging Matthew from Amigakit multiple times with no reply back. I am fed up with this machine now and don't want to deal with it any longer.
I hear ya and been there too damn many times with my miggies over the years....December is really difficult time to get hold of anyboby over the pond as (especially Europeans) don't take our point of view on 'vacation" with us a week ...max 2 weeks is most of us working stiffs can get but those guys...man I tell ya more like a month to 6 weeks :o
-
Any difference if you choose VGA/DVI/HDMI over the other? In other words: tried all video outputs?
-
Yup, doesnt matter what I use.
-
U-Boot variables from serial out
X5000> printenv
amigaboot_quiet=Y
amigabootmenu_default=0
baudrate=115200
bdev=sda3
bootargs=root=/dev/sda2 mem=3500M console=ttyS0,115200 console=tty0
bootargs_live=root=/dev/ramdisk boot=casper mem=3500M ro --
bootargs_live_debug=root=/dev/ramdisk boot=casper mem=3500M ro break debug
bootcmd=setenv bootargs root=/dev/$bdev rw console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
bootdelay=10
bootdvd=scsi reset ; load scsi 0 2000000 boot_dvd ; bootm 2000000
bootfile=uImage
consoledev=ttyS0
eth1addr=00:80:10:11:07:08
ethact=FM1@DTSEC4
ethaddr=00:80:10:11:07:07
ethernetboot=echo Running Ethernet Boot
ethprime=FM1@DTSEC4
fdtaddr=c00000
fman_ucode=7fe733f0
harddiskboot=echo Running Hard Disk Boot
hwconfig=fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1;usb1:dr_mode=host,phy_type=utmi;usb2:dr_mode=host,phy_type=utmi
linuxboot=echo Running Linux
liveusb=usb start ; setenv bootargs_live_debug ; ext2load usb 1:1 2000000 boot_dvd ; bootm 2000000
loadaddr=1000000
loadbmps=mmc read 0x10005000 0x500 0x200; mmc read 0x20000000 0x10000 0x20000
massboot=usb reset ; boota
mos=bootmorphos
netdev=eth0
nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
opticalboot=echo Running Optical Boot
preboot=run loadbmps;bmp d 0x20000000;ami
ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr $ramdiskaddr $fdtaddr
ramdiskaddr=2000000
ramdiskfile=ramdisk.uboot
rootpath=/opt/nfsroot
scsidevs=1
stdin=usbkbd,serial
stdout=serial,vga
uboot=u-boot.bin
ubootaddr=0xFFF80000
Environment size: 1917/8188 bytes
-
Hey Acill,
I might be wrong, be from the serial log I don't it recognizing your HD. Do you have any installed?
If not, do you have the boot CD in the dvd drive?
If that doesn't work, when you tried with the boot USB, you selected to "Boot from mass storage" at the boot menu, right? Did you connect the USB at the first USB port, at the back, top in the row, closer to the back of the tower?
Keep on using the serial connection because it will help you with messages.
-
Also only if you made a custom Recovery CD or USB thumb drive wich includes the Radeon Rx driver will it be able to boot with the Radeon RX card from the Recovery media.
-
PAcking it up!
-
Thanks for all the reply in this.
As for the RAM issue. I noticed that and posted the 2nd serial log because it was reading the RAM bad or something I though in the first. I am not mixing RAM and they are in pairs. The first set is a pair of 2GB sticks from Corsair that the machine shipped with. The other is a pair of HyperX 8GB that was working perfectly before all this and was recommended and tested from AOTL for X5000 use.
The USB devices installed are only the keyboard and mouse. The other stuff its showing is the internal USB headers and ports. Nothing USB is connected.
I have tried with my DVD out, HDD out, USB stick in upper slot, CD install disk, all are the same result as this.
I have used new SATA cables, changed ports, no change.
I have replaced the CR22 coin cell with a new one that I measured the voltage on and was a good 3.4V
I tried a new HDD and it wont boot from USB or CD to get to the point of installing as mentioned, so no good.
I have tried with three different video cards. #1 it shipped new with was a R250X (7750) #2 is a HD6950, #3 was the primary card id been using with the newer enhancer 2.0 beta and drivers and is a 560. I know the last card wont boot from the CD and work, buiut the other two should, and #1 has several times before. I have restored my system a few times in the past from CD and USB.
As I mentioned, I can replace the GPU with the 6950 and put in my MorphOS HDD and it boots into it perfectly, so its SOMETHING to do with OS4.1 or something in U-Boot that magicly change while powered off for the last couple weeks I was gone on work trips that's caused this.
I got fed up and packed it away, so no idea what to do, and A-eon isn't really helping much. Trevor asked me to do a lot of what you all said, and its not changed anything.
-
Wow.... really sorry to here this Paul. :-\ Keep us up to date if you have any epiphanies!
-
For now I am giving up. Since all boot media fails I am more in line to thinking its the video driver not compatible, but I have booted from the CD before to restore as well as this USB drive so not sure what the deal is.
-
@Acill
even my X5000 has always been very temperamental, now I use it with MorphOS, my advice is to install a radeon HD 5450 and start the computer via the official Prerelease with thumbdrive. I'm sorry and I hope for better support ....... !!!
-
5450? Will this one work? It was cheap enough to get it and take a chance.
https://www.amazon.com/Diamond-Multimedia-Express-Graphics-5450PE31G/dp/B006MBP7R2/ref=pd_lpo_147_t_1/140-1138464-8662800?_encoding=UTF8&pd_rd_i=B006MBP7R2&pd_rd_r=1a1b9129-f315-4a03-91ac-56810885d957&pd_rd_w=qgtPe&pd_rd_wg=hsrFE&pf_rd_p=7b36d496-f366-4631-94d3-61b87b52511b&pf_rd_r=PRDCK9DMDDAHA6FNQYGZ&psc=1&refRID=PRDCK9DMDDAHA6FNQYGZ
-
I don’t know, but I Think yes. I Have Sapphire HD5450 1G DDR3 HDMI/DVI-I/VGA, very similar.
-
Might as well give it try! It's cheap! 8)
-
Sorry to hear about your problem.
my 2 cents to try to help you is my u-boot config in case there is something in mine that would boot OS4 that you might not have...
11.DH0:> nvgetvar
amigaboot_quiet=N
amigabootmenu_animcycles=1
baudrate=115200
bdev=sda3
bootargs=root=/dev/sda2 mem=3500M console=ttyS0,115200 console=tty0
bootargs_live=root=/dev/ramdisk boot=casper mem=3500M ro --
bootargs_live_debug=root=/dev/ramdisk boot=casper mem=3500M ro break debug
bootcmd=setenv bootargs root=/dev/$bdev rw console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
bootdelay=5
bootdvd=scsi reset ; load scsi 0 2000000 boot_dvd ; bootm 2000000
bootfile=uImage
bootmenu_waitticks=50
consoledev=ttyS0
eth1addr=00:50:C2:20:DA:CC
ethact=FM1@DTSEC4
ethaddr=00:50:C2:20:DA:CB
ethernetboot=echo Running Ethernet Boot
ethprime=FM1@DTSEC4
fdtaddr=c00000
fman_ucode=7fe73478
harddiskboot=echo Running Hard Disk Boot
hwconfig=fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1;usb1:dr_mode=host,phy_type=utmi;usb2:dr_mode=host,phy_type=utmi
kbddev_norwin=1
linuxboot=echo Running Linux
liveusb=usb start ; setenv bootargs_live_debug ; ext2load usb 1:1 2000000 boot_dvd ; bootm 2000000
loadaddr=1000000
loadbmps=mmc read 0x10005000 0x500 0x200; mmc read 0x20000000 0x10000 0x20000
massboot=echo Running Mass Storage Boot
mos=bootmorphos
netdev=eth0
nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
opticalboot=echo Running Optical Boot
preboot=run loadbmps;bmp d 0x20000000;ami
ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr $ramdiskaddr $fdtaddr
ramdiskaddr=2000000
ramdiskfile=ramdisk.uboot
rootpath=/opt/nfsroot
scsidevs=1
sii3112ide_conf=01
stdin=usbkbd,serial
stdout=serial,vga
uboot=u-boot.bin
ubootaddr=0xFFF80000
-
The issue, sounds exactly like a GFX card / loose cable issue.
I would try another GFX card. If you have the USB boot sitck, I make, then its tested with a 6570. I have also tested them on 6450 also work.
-
Do you have an image of this USB boot stick I can try?My question is why have I been able to boot from CD and USB in the past if I had to restore but now I cant? Its something odd happening.
-
You might check if the monitor cable is hdmi only.
Try DVI to hdmi.
The machine is fine (my guess) just not the right video card with the right driver and video cable!
Really,
Michael
-
Do you have an image of this USB boot stick I can try?My question is why have I been able to boot from CD and USB in the past if I had to restore but now I cant? Its something odd happening.
Is a mystery indeed. As posted above, I also use DVI when testing.
Have you changed anything in UBOOT? could try reflashing current Firmware on to card.
-
So once again, by pure magic, it works again. I did nothing other than had it off for a couple of days. I just got my Radeon 5450 in and tried it, booted right up. Put my Polaris 11 card in again, booted right up. I just don't understand this machine sometimes?!
I am not joking, I did nothing other than power it off a couple of days, swap cards (keeping in mind I had been swapping cards before the 5450 came in), and Poof, it works.
-
Amiga Magic! ;D
Hope she stays afloat!
Happy New Year Acill! 8)
-
phew! Now never switch it off!
-
You joke, but its been on since last boot, lol!
-
Maybe some wierd static charge?
I have had electronics be effected by static, try them next day and they work fine after not booting at all.
I find my Amiga does this more often than not, after messing with it.