Amiga.org
Amiga computer related discussion => Amiga Hardware Issues and discussion => Topic started by: gary2000 on June 14, 2019, 02:48:11 PM
-
It's coming along...
-
If you have any issues let me know! Also here is some good resource to help you. Its a part placement guide that John Hertell had another user help us put together. It makes builds a lot easier.
http://www.hertell.nu/locator/locator.php?project=A4000
-
Thank you. I'm sure I will have questions.
Yes, that placement tool works well!
-
Would anybody know what the part number is for the 6 pin power connector? I bought amp 350711-1, which looks to be correct, but has male contacts instead of female.
-
I'll see if I can find it for you here in a bit. I am in Australia currently and need to search Mouser carts for my past orders.
-
Here it is: https://www.mouser.com/ProductDetail/TE-Connectivity-AMP/350827-1?qs=%2Fha2pyFaduhO9K6hFWyj%252B9di953Oe11BRMqF7eT3GVg8f210t5DoTg%3D%3D
Mouser Part: 571-350827-1
-
Thanks !
-
First test result is a black screen , with video sync and no serial output to diagrom . Clocks look okay and voltages are fine , except -12 measures -11.13
Should sclk on Lisa be 3.571 MHz?
Should ECLK on U300 CIA be 714 KHz?
kbrst is always held low . Should this go high on reboot?
Seems to be no activity on Paula, Gary , Alice address lines
This seems to be a global issue keeping the system down .
Any other basic items I should check ? I'm trying to be methodical, but find myself stabbing in the dark .
-
It's working!
Fail pin was pulled low by power supply PG brown/ gray cable, so Gary would not reset . In Skynet power supply , IC7 I suspect is bad . I got impatient, and just cut the wire and ran to five volts.
Diagrom checksum test okay, CPU and chip ram is seen .
Hangs on fast ram check . But, that's progress .
-
Thanks Acill! You and Chucky have saved the Amiga hardware community.
-
Thanks Acill! You and Chucky have saved the Amiga hardware community.
Absolutely !
-
Well, moving along smoothly until I inserted the Zorro daughterboard. The computer will boot one out of 10 times with errors if the daughterboard is in place . It works flawlessly without it , so far with diagrom. Will not boot with original ROMs , though.
Anybody have a similar issue ? So far, checking u701/U714 pals , buster and the CPU are involved as well.
Will not be very expandable at this point , weird .
-
Just to update:
Replaced PAL U714 which corrected zorro II problem.
With diagrom, CPU okay, chip RAM tested okay, fast RAM ok, all video and audio tests okay, IRQ/CIA okay, zorro II detected ram card, IDE detected correctly, floppy drive seen.
With 3.0 roms will not boot, resets, and then stops after screen turns on.
OVL = L with diagrom and H with 3.0 rom, is that normal?
Anyone have any other suggestions to check for?
Are 3.1 roms available for download to burn for me to purchase? I do not want 3.1.4 at this time.
-
I do not want 3.1.4 at this time.
Why not ? They are much more better than 3.1..... using big harddrives for example….
-
I do not want 3.1.4 at this time.
Why not ? They are much more better than 3.1..... using big harddrives for example….
I read this a lot here and there (mostly YouTube). I and many others use large hard drives under 2.0, never mind 3.1.4. ;)
-
I have nothing against 3.1.4, I only wanted 3.1 to test with. (Have enough unknown variables to deal with).
-
The only issue I had with running diagrom was a vertical hold problem rolling screen.
Could someone tell me the in-circuit value of R514, which shows 10K? Mine is 3K or 4.5K without resistor, and this does not seem normal.
-
Well, it finally booted to Kick start screen!
The Commodore roms went bad, which was surprising.
One issue other than the occasional yellow screen, is when you put in a disk OVL is held high. You must turn off and turn on again for the high to low to happen. Has anyone seen this happen?
Most games will not fully load and there is graphical corruption when trying, but work bench will load fine.
-
Mostly working at this point, but I have the following issues:
When selecting from Gotek, you have to manually turn off the power and turn on to reboot instead of warm restart.
Fast RAM 4MB shows as 1 - I believe this has to do with the power supply _fail + 5 V as shown in other posts.
Only Gotek works as DF0 and original floppy is unstable and does not load much. All jumpers were set correctly.
Sysinfo reports and ECS Agnus instead of Alice AGA. It also shows 25 mhz as 030, even though it is an 040. It sometimes reports as 16 mhz, also using Sysinfo 4.3.
Some games work perfectly and some crash. Workbench loads ok. Any ideas on these issues?
-
Sysinfo reports and ECS Agnus instead of Alice AGA. It also shows 25 mhz as 030, even though it is an 040.
Sounds like you're missing SetPatch in Startup-Sequence - it is SetPatch that enables AGA and loads 68040.library.
You say Workbench loads OK, but if you go to Prefs/Screenmode, I suspect it also doesn't let you pick 256 colour modes.
-
Ok, thanks. I will check into that.
-
Ended up installing bestWB. Showconfig looked ok / 256 colors working.
Sysinfo still showing ECS Agnus - 2 / 68040 16.60 with IDE drive attached and 25.60 with no hard drive.
Checked and replaced gals for IDE, no difference. I wonder if the MMULIB is the one included in bestWB. In startup-sequence it says CPU checkinstall. Hopefully this is just a configuration issue.